NSK

NSK Deep Groove Ball Bearings 6808 ,Single-Row  D=40 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6808 40 52 7 0.3 6.35 5.55 12000 14000 17 0.031 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6807 ,Single-Row  D=35 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6807 35 47 7 0.3 4.9 4.1 14000 16000 16.7 0.027 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6806 ,Single-Row  D=30 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6806 30 42 7 0.3 4.7 3.65 15000 18000 16.4 0.024 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6805 ,Single-Row  D=25 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6805 25 37 7 0.3 4.5 3.15 18000 22000 16.1 0.021 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6804 ,Single-Row  D=20 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6804 20 32 7 0.3 4 2.47 22000 26000 15.5 0.017 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6803 ,Single-Row  D=17 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6803 17 26 5 0.3 2.63 1.57 26000 30000 15.7 0.007 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6802 ,Single-Row  D=15 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6802 15 24 5 0.3 2.07 1.26 28000 34000 15.8 0.007 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6801 ,Single-Row  D=12 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6801 12 21 5 0.3 1.92 1.04 32000 38000 15.3 0.006 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6800 ,Single-Row  D=10 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6800 10 19 5 0.3 1.72 0.84 34000 40000 14.8 0.005 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6332ZZS ,Single-Row  D=160   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6332ZZS 160 340 68 4 278 287 1700 　 13.9 26.2   DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6330ZZS ,Single-Row  D=150   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6330ZZS 150 320 65 4 274 284 1800 　 13.9 22.7   DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6328ZZS ,Single-Row  D=140   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6328ZZS 140 300 62 4 253 246 2000 　 13.6 18.5   DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6326ZZS ,Single-Row  D=130   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6326ZZS 130 280 58 4 229 214 2200 　 13.6 15.2   DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6324ZZ ,Single-Row  D=120   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6324ZZ 120 260 55 3 207 185 2200 　 13.5 12.5   DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6322ZZ ,Single-Row  D=110   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6322ZZ 110 240 50 3 205 179 2400 　 13.2 9.51   DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6321ZZ ,Single-Row  D=105   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6321ZZ 105 225 49 3 184 154 2600 　 13.2 8.09 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6320ZZ ,Single-Row  D=100   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6320ZZ 100 215 47 3 173 141 2800 　 13.2 7.04 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6319ZZ ,Single-Row  D=95   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6319ZZ 95 200 45 3 153 119 3000 　 13.3 5.76 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6318ZZ ,Single-Row  D=90   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6318ZZ 90 190 43 3 143 107 3600 　 13.3 4.98 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6317ZZ ,Single-Row  D=85   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6317ZZ 85 180 41 3 133 97 3800 　 13.3 4.28 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6316ZZ ,Single-Row  D=80   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6316ZZ 80 170 39 2.1 123 86.5 4000 　 13.3 3.67 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6324DDU ,Single-Row  D=120   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6324DDU 120 260 55 3 207 185 1800 　 13.5 12.5   DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6321DDU ,Single-Row  D=105 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6321DDU 105 225 49 3 184 154 2000 　 13.2 8.09   DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6320DDU ,Single-Row  D=100 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6320DDU 100 215 47 3 173 141 2200 　 13.2 7.04   DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6319DDU ,Single-Row  D=95 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6319DDU 95 200 45 3 153 119 2400 　 13.3 5.76 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6318DDU ,Single-Row  D=90 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6318DDU 90 190 43 3 143 107 2400 　 13.3 4.98 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6317DDU ,Single-Row  D=85 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6317DDU 85 180 41 3 133 97 2600 　 13.3 4.28 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6320VV ,Single-Row  D=100 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6320VV 100 215 47 3 173 141 2800 0 13.2 7.04 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6319VV ,Single-Row  D=95 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6319VV 95 200 45 3 153 119 3000 0 13.3 5.76 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6318VV ,Single-Row  D=90 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6318VV 90 190 43 3 143 107 3600 0 13.3 4.98 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6317VV ,Single-Row  D=85 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6317VV 85 180 41 3 133 97 3800 0 13.3 4.28 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 68/800 ,Single-Row  D=800 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 68/800 800 980 82 5 530 1310 400 480 17.5 132 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 68/750 ,Single-Row  D=750 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 68/750 750 920 78 5 525 1260 430 530 17.4 110 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 68/710 ,Single-Row  D=710 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 68/710 710 870 74 4 480 1100 480 560 17.4 92.6 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 68/670 ,Single-Row  D=670 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 68/670 670 820 69 4 435 965 500 630 17.4 75.4 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 68/630 ,Single-Row  D=630 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 68/630 630 780 69 4 420 890 560 670 17.3 71.3 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 68/600 ,Single-Row  D=600 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 68/600 600 730 60 3 355 735 600 710 17.5 50.9 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 68/560 ,Single-Row  D=560 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 68/560 560 680 56 3 330 650 670 800 17.4 41.5 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 68/530 ,Single-Row  D=530 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 68/530 530 650 56 3 325 625 710 850 17.4 39.8 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 68/500 ,Single-Row  D=500 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 68/500 500 620 56 3 320 600 750 900 17.3 37.2 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6356 ,Single-Row  D=280 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6356 280 580 108 6 570 840 900 1100 14.5 144 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6352 ,Single-Row  D=260 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6352 260 540 102 6 505 710 1000 1200 14.6 118 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6348 ,Single-Row  D=240 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6348 240 500 95 5 470 625 1100 1300 14.2 94.4 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6344 ,Single-Row  D=220 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6344 220 460 88 5 410 520 1200 1500 14.3 73.9 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6340 ,Single-Row  D=200 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6340 200 420 80 5 380 445 1300 1600 13.8 55.3 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6338M ,Single-Row  D=190 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6338M 190 400 78 5 355 415 1400 1700 14.1 49.7 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6336M ,Single-Row  D=180 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6336M 180 380 75 4 355 405 1500 1800 13.9 43.1 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6334M ,Single-Row  D=170 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6334M 170 360 72 4 325 355 1600 2000 13.6 36.6 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less