NTN Deep Groove Ball Bearings

Item # d D B r Static Load Rating Dynamic Load Rating 16028 5.5118 in 140.000 mm 8.2677 in 210.000 mm 0.8661 in 22.000 mm 0.0433 in 1.100 mm 19100 lbf 85000 N 85.00 kN 20450 lbf 91000 N 91.00 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 16026 5.1181 in 130.000 mm 7.8740 in 200.000 mm 0.8661 in 22.000 mm 0.0433 in 1.100 mm 17870 lbf 79500 N 79.50 kN 19890 lbf 88500 N 88.50 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 16024 4.7244 in 120.000 mm 7.0866 in 180.000 mm 0.7480 in 19.000 mm 0.0394 in 1.000 mm 14270 lbf 63500 N 63.50 kN 15730 lbf 70000 N 70.00 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 16022 4.3307 in 110.000 mm 6.6929 in 170.000 mm 0.7480 in 19.000 mm 0.0394 in 1.000 mm 12700 lbf 56500 N 56.50 kN 14270 lbf 63500 N 63.50 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 16021 4.1339 in 105.000 mm 6.2992 in 160.000 mm 0.7087 in 18.000 mm 0.0394 in 1.000 mm 11350 lbf 50500 N 50.50 kN 12920 lbf 57500 N 57.50 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 16020 3.9370 in 100.000 mm 5.9055 in 150.000 mm 0.6299 in 16.000 mm 0.0394 in 1.000 mm 8200 lbf 36500 N 36.50 kN 8760 lbf 39000 N 39.00 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Inner Dia 10 mm Deep Groove Ball Bearing 6000LLU   SPECIFICATIONS Type of Product : Deep Groove Ball Bearing Model No : 6000LLU Width : 8 mm Inner Diameter : 10 mm       1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 16019 3.7402 in 95.000 mm 5.7087 in 145.000 mm 0.6299 in 16.000 mm 0.0394 in 1.000 mm 7860 lbf 35000 N 35.00 kN 8540 lbf 38000 N 38.00 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 16018 3.5433 in 90.000 mm 5.5118 in 140.000 mm 0.6299 in 16.000 mm 0.0394 in 1.000 mm 7530 lbf 33500 N 33.50 kN 8310 lbf 37000 N 37.00 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 16017 3.3465 in 85.000 mm 5.1181 in 130.000 mm 0.5512 in 14.000 mm 0.0236 in 0.600 mm 5880 lbf 26200 N 26.20 kN 6450 lbf 28700 N 28.70 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 16016 3.1496 in 80.000 mm 4.9213 in 125.000 mm 0.3937 in 10.000 mm 0.0236 in 0.600 mm 5640 lbf 25100 N 25.10 kN 6310 lbf 28100 N 28.10 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 16015 2.9528 in 75.000 mm 4.5276 in 115.000 mm 0.5118 in 13.000 mm 0.0236 in 0.600 mm 5390 lbf 24000 N 24.00 kN 6200 lbf 27600 N 27.60 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 16014 2.7559 in 70.000 mm 4.3307 in 110.000 mm 0.5118 in 13.000 mm 0.0236 in 0.600 mm 5080 lbf 22600 N 22.60 kN 6060 lbf 27000 N 27.00 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 16013 2.5591 in 65.000 mm 3.9370 in 100.000 mm 0.4331 in 11.000 mm 0.0236 in 0.600 mm 4200 lbf 18700 N 18.70 kN 5100 lbf 22700 N 22.70 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 16012 2.3622 in 60.000 mm 3.7402 in 95.000 mm 0.4331 in 11.000 mm 0.0236 in 0.600 mm 3930 lbf 17500 N 17.50 kN 4960 lbf 22100 N 22.10 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 16011 2.1654 in 55.000 mm 3.5433 in 90.000 mm 0.4331 in 11.000 mm 0.0236 in 0.600 mm 3430 lbf 15300 N 15.30 kN 4630 lbf 20600 N 20.60 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 16008 1.5748 in 40.000 mm 2.6772 in 68.000 mm 0.3543 in 9.000 mm 0.0118 in 0.300 mm 2160 lbf 9650 N 9.65 kN 3140 lbf 14000 N 14.00 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 16007 1.3780 in 35.000 mm 2.4409 in 62.000 mm 0.3543 in 9.000 mm 0.0118 in 0.300 mm 1840 lbf 8200 N 8.20 kN 2900 lbf 12900 N 12.90 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 16005 0.9843 in 25.000 mm 1.8504 in 47.000 mm 0.3150 in 8.000 mm 0.0118 in 0.300 mm 1140 lbf 5100 N 5.10 kN 2070 lbf 9250 N 9.25 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 16004 0.7874 in 20.000 mm 1.6535 in 42.000 mm 0.3150 in 8.000 mm 0.0118 in 0.300 mm 1010 lbf 4500 N 4.50 kN 1960 lbf 8750 N 8.75 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 16003 0.6693 in 17.000 mm 1.3780 in 35.000 mm 0.3150 in 8.000 mm 0.0118 in 0.300 mm 750 lbf 3350 N 3.35 kN 1690 lbf 7550 N 7.55 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings 6815C3, D=75 Single Row Radial Ball Bearing - Open Type SPECIFICATIONS Bore Type Round Bore Diameter 75 mm Outside Diameter 95 mm Overall Width 10 mm Closure Type Open Internal Clearance C3 Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 3120 lbf Static Load Capacity 2900 lbf Precision Rating Class 0 Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 0.3937 in, 10.000 mm Outer Ring Width 0.3937 in; 10.000 mm Maximum RPM (Grease) 6400 RPM Fillet Radius 0.600 mm, 0.0236 in Maximum RPM 7600 RPM Weight 0.317 lb 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings 6811C3, D=55 Radial/Deep Groove Ball Bearing - Round Bore, 55 mm ID, 72 mm OD, 9 mm Width, Open, C3 Internal Clearance   SPECIFICATIONS Bore Type Round Bore Diameter 55 mm Outside Diameter 72 mm Overall Width 9 mm Closure Type Open Internal Clearance C3 Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 2190 lbf Static Load Capacity 1820 lbf Precision Rating Class 0 Seal Type None Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 9.000 mm, 0.3543 in Outer Ring Width 0.3543 in; 9.000 mm Maximum RPM (Grease) 8700 RPM Fillet Radius 0.300 mm, 0.0118 in Maximum RPM 10000 RPM Manufacturer UPC Number 4547359006278 Harmonization Code 8482.10.5052 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings 6332C3, D=160 Radial/Deep Groove Ball Bearing - Round Bore, 160 mm ID, 340 mm OD, 68 mm Width, Open, C3 Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 160.000 mm, 6.2992 in Outside Diameter 340.000 mm, 13.3858 in Overall Width 68.000 mm, 2.6772 in Closure Type Open Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 69690 lbf Static Load Capacity 64290 lbf Precision Rating Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 68.000 mm, 2.6772 in Outer Ring Width 2.6772 in; 68.000 mm Maximum RPM (Grease) 1900 RPM Maximum RPM (Oil) 2300 rpm Fillet Radius 4.000 mm, 0.1575 in Maximum RPM 2300 RPM Manufacturer UPC Number 4547359404227 Weight 57.98 lbs Harmonization Code 8482.10.5056 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings 6320C3, D=100 Radial/Deep Groove Ball Bearing - Round Bore, 100 mm ID, 215 mm OD, 47 mm Width, Open, C3 Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 100.000 mm, 3.9370 in Outside Diameter 215.000 mm, 8.4646 in Overall Width 1.8504 in, 47.000 mm Closure Type Open Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 43160 lbf Static Load Capacity 31690 lbf Precision Rating Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 1.8504 in, 47.000 mm Outer Ring Width 1.8504 in; 47.000 mm Maximum RPM (Grease) 3200 RPM Maximum RPM (Oil) 3700 rpm Fillet Radius 0.1181 in, 3.000 mm Maximum RPM 3700 RPM Series 63 Manufacturer UPC Number 4547359006018 Weight 3.05 lbs Harmonization Code 8482.10.5056 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings 6318C3, D=90 Radial/Deep Groove Ball Bearing - Round Bore, 90 mm ID, 190 mm OD, 43 mm Width, Open, C3 Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 90.000 mm, 3.5433 in Outside Diameter 190.000 mm, 7.4803 in Overall Width 43.000 mm, 1.6929 in Closure Type Open Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 35510 lbf Static Load Capacity 24050 lbf Precision Rating Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 43.000 mm, 1.6929 in Outer Ring Width 1.6929 in; 43.000 mm Maximum RPM (Grease) 3600 RPM Maximum RPM (Oil) 4200 rpm Fillet Radius 0.1181 in, 3.000 mm Maximum RPM 4200 RPM Series 63 Manufacturer UPC Number 4547359005936 Weight 10.80 lbs Harmonization Code 8482.10.5056 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings 6317C3, D=85 Radial/Deep Groove Ball Bearing - Round Bore, 85 mm ID, 180 mm OD, 41 mm Width, Open, C3 Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 3.3465 in, 85.000 mm Outside Diameter 180.000 mm, 7.0866 in Overall Width 41.000 mm, 1.6142 in Closure Type Open Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 33040 lbf Static Load Capacity 21800 lbf Precision Rating Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 41.000 mm, 1.6142 in Outer Ring Width 1.6142 in; 41.000 mm Maximum RPM (Grease) 3800 RPM Maximum RPM (Oil) 4500 rpm Fillet Radius 0.1181 in, 3.000 mm Maximum RPM 4500 RPM Manufacturer UPC Number 4547359005899 Weight 9.26 lbs Harmonization Code 8482.10.5056 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings 6315C3, D=75 Radial/Deep Groove Ball Bearing - Round Bore, 75 mm ID, 160 mm OD, 37 mm Width, Open, C3 Internal Clearance Bore Type Round Bore Diameter 75.000 mm, 2.9528 in Outside Diameter 160.000 mm, 6.2992 in Overall Width 37.000 mm, 1.4567 in Closure Type Open Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 28320 lbf Static Load Capacity 17310 lbf Precision Rating Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 37.000 mm, 1.4567 in Outer Ring Width 1.4567 in; 37.000 mm Maximum RPM (Grease) 4300 RPM Maximum RPM (Oil) 5000 rpm Fillet Radius 0.0827 in, 2.100 mm Maximum RPM 5000 RPM Series 63 Manufacturer UPC Number 4547359005813 Weight 6.64 lbs 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings 6313C3, D=65 Radial/Deep Groove Ball Bearing - Round Bore, 65 mm ID, 140 mm OD, 33 mm Width, Open, C3 Internal Clearance Bore Type Round Bore Diameter 65.000 mm, 2.5591 in Outside Diameter 140.000 mm, 5.5118 in Overall Width 33.000 mm, 1.2992 in Closure Type Open Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 23150 lbf Static Load Capacity 13480 lbf Precision Rating Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 33.000 mm, 1.2992 in Outer Ring Width 1.2992 in; 33.000 mm Maximum RPM (Grease) 4900 RPM Maximum RPM (Oil) 5800 rpm Fillet Radius 0.0827 in, 2.100 mm Maximum RPM 5800 RPM Series 63 Manufacturer UPC Number 4547359005738 Weight 4.57 lbs 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings 6924, D=120 Radial/Deep Groove Ball Bearing - Round Bore, 120 mm ID, 165 mm OD, 22 mm Width, Open, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 120.000 mm, 4.7244 in Outside Diameter 6.4961 in, 165.000 mm Overall Width 0.8661 in, 22.000 mm Closure Type Open Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 13260 lbf Static Load Capacity 12130 lbf Precision Rating Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 0.8661 in, 22.000 mm Outer Ring Width 0.8661 in; 22.000 mm Maximum RPM (Grease) 3800 RPM Maximum RPM (Oil) 4400 rpm Fillet Radius 1.100 mm, 0.0433 in Maximum RPM 4400 RPM Series 69 Manufacturer UPC Number 4547359423464 Weight 2.63 lbs Harmonization Code 8482.10.5056 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings 6915, D=75 Single Row Radial Ball Bearing - Open Type SPECIFICATIONS Bore Type Round Bore Diameter 75 mm, 2.9528 in Outside Diameter 105 mm, 4.1339 in Overall Width 16 mm, 0.6299 in Closure Type Open Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 6060 lbf Static Load Capacity 5080 lbf Precision Rating Class 0 Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 16.000 mm, 0.6299 in Outer Ring Width 0.6299 in; 16.000 mm Maximum RPM (Grease) 6100 RPM Fillet Radius 1.000 mm, 0.0394 in Maximum RPM 7200 RPM Manufacturer UPC Number 4547359006995 Harmonization Code 8482.10.5056 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings 6911, D=55 Radial/Deep Groove Ball Bearing - Round Bore, 55 mm ID, 80 mm OD, 13 mm Width, Open, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 55.000 mm, 2.1654 in Outside Diameter 3.1496 in, 80.000 mm Overall Width 13.000 mm, 0.5118 in Closure Type Open Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 3970 lbf Static Load Capacity 2980 lbf Precision Rating Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 13.000 mm, 0.5118 in Outer Ring Width 0.5118 in; 13.000 mm Maximum RPM (Grease) 8200 RPM Maximum RPM (Oil) 9600 rpm Fillet Radius 1.000 mm, 0.0394 in Maximum RPM 9600 RPM Series 69 Manufacturer UPC Number 4547359006919 Weight 0.40 lbs Harmonization Code 8482.10.5052 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings 6907, D=35 Radial/Deep Groove Ball Bearing - Round Bore, 35 mm ID, 55 mm OD, 10 mm Width, Open, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 35.000 mm, 1.3780 in Outside Diameter 55.000 mm, 2.1654 in Overall Width 0.3937 in, 10.000 mm Closure Type Open Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 2380 lbf Static Load Capacity 1530 lbf Precision Rating Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 0.3937 in, 10.000 mm Outer Ring Width 0.3937 in; 10.000 mm Maximum RPM (Grease) 12000 RPM Maximum RPM (Oil) 15000 rpm Fillet Radius 0.600 mm, 0.0236 in Maximum RPM 15000 RPM Series 69 Manufacturer UPC Number 4547359006759 Weight 0.17 lbs Harmonization Code 8482.10.5052 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings 6905, D=25 Radial/Deep Groove Ball Bearing - Round Bore, 25 mm ID, 42 mm OD, 9 mm Width, Open, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 0.9843 in, 25.000 mm Outside Diameter 42.000 mm, 1.6535 in Overall Width 9.000 mm, 0.3543 in Closure Type Open Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 1750 lbf Static Load Capacity 1020 lbf Precision Rating Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 9.000 mm, 0.3543 in Outer Ring Width 0.3543 in; 9.000 mm Maximum RPM (Grease) 16000 RPM Maximum RPM (Oil) 19000 rpm Fillet Radius 0.300 mm, 0.0118 in Maximum RPM 19000 RPM Series 69 Manufacturer UPC Number 4547359006674 Weight 0.10 lbs Harmonization Code 8482.10.5048 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings 6901, D=12 Radial/Deep Groove Ball Bearing - Round Bore, 12 mm ID, 24 mm OD, 6 mm Width, Open, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 0.4724 in, 12.000 mm Outside Diameter 24.000 mm, 0.9449 in Overall Width 6.000 mm, 0.2362 in Closure Type Open Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 710 lbf Static Load Capacity 320 lbf Precision Rating Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 6.000 mm, 0.2362 in Outer Ring Width 0.2362 in; 6.000 mm Maximum RPM (Grease) 27000 RPM Maximum RPM (Oil) 32000 rpm Fillet Radius 0.300 mm, 0.0118 in Maximum RPM 32000 RPM Series 69 Manufacturer UPC Number 4547359006513 Weight 0.02 lbs Harmonization Code 8482.10.5044 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings 6832, D=160 Radial/Deep Groove Ball Bearing - Round Bore, 160 mm ID, 200 mm OD, 20 mm Width, Open, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 160.000 mm, 6.2992 in Outside Diameter 200.000 mm, 7.8740 in Overall Width 20.000 mm, 0.7874 in Closure Type Open Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 12020 lbf Static Load Capacity 12810 lbf Precision Rating Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 20.000 mm, 0.7874 in Outer Ring Width 0.7874 in; 20.000 mm Maximum RPM (Grease) 2900 RPM Maximum RPM (Oil) 3400 rpm Fillet Radius 1.100 mm, 0.0433 in Maximum RPM 3400 RPM Series 68 Manufacturer UPC Number 4547359414530 Weight 2.67 lbs Harmonization Code 8482.10.5056 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings 6828, D=140 Radial/Deep Groove Ball Bearing - Round Bore, 140 mm ID, 175 mm OD, 18 mm Width, Open, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 140.000 mm, 5.5118 in Outside Diameter 175.000 mm, 6.8898 in Overall Width 18.000 mm, 0.7087 in Closure Type Open Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 9550 lbf Static Load Capacity 10000 lbf Precision Rating Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 18.000 mm, 0.7087 in Outer Ring Width 0.7087 in; 18.000 mm Maximum RPM (Grease) 3400 RPM Maximum RPM (Oil) 4000 rpm Fillet Radius 1.100 mm, 0.0433 in Maximum RPM 4000 RPM Manufacturer UPC Number 4547359414387 Weight 1.83 lbs Harmonization Code 8482.10.5056 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings 6816, D=80 Single Row Radial Ball Bearing - Open Type SPECIFICATIONS Bore Type Round Bore Diameter 80 mm, 3.1496 in Outside Diameter 100 mm, 3.9370 in Overall Width 10 mm, 0.3937 in Closure Type Open Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 3140 lbf Static Load Capacity 2980 lbf Precision Rating Class 0 Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 0.3937 in, 10.000 mm Outer Ring Width 0.3937 in; 10.000 mm Maximum RPM (Grease) 6000 RPM Fillet Radius 0.600 mm, 0.0236 in Maximum RPM 7100 RPM Manufacturer UPC Number 4547359006377 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings 6813, D=65 Single Row Radial Ball Bearing - Open Type SPECIFICATIONS Bore Type Round Bore Diameter 65 mm, 2.5591 in Outside Diameter 85 mm, 3.3465 in Overall Width 10 mm, 0.3937 in Closure Type Open Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 2870 lbf Static Load Capacity 2470 lbf Precision Rating Class 0 Seal Type None Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 0.3937 in, 10.000 mm Outer Ring Width 0.3937 in; 10.000 mm Maximum RPM (Grease) 7400 RPM Fillet Radius 0.600 mm, 0.0236 in Maximum RPM 8700 RPM Manufacturer UPC Number 4547359006315 Harmonization Code 8482.10.5052 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings 6808, D=40 Radial/Deep Groove Ball Bearing - Round Bore, 40 mm ID, 52 mm OD, 7 mm Width, Open, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 1.5748 in, 40.000 mm Outside Diameter 52.000 mm, 2.0472 in Overall Width 7.000 mm, 0.2756 in Closure Type Open Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 1270 lbf Static Load Capacity 980 lbf Precision Rating Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 7.000 mm, 0.2756 in Outer Ring Width 0.2756 in; 7.000 mm Maximum RPM (Grease) 12000 RPM Maximum RPM (Oil) 14000 rpm Fillet Radius 0.300 mm, 0.0118 in Maximum RPM 14000 RPM Manufacturer UPC Number 4547359006216 Weight 0.07 lbs Harmonization Code 8482.10.5048 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings 6804, D=20 Radial/Deep Groove Ball Bearing - Round Bore, 20 mm ID, 32 mm OD, 7 mm Width, Open, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 20.000 mm, 0.7874 in Outside Diameter 1.2598 in, 32.000 mm Overall Width 7.000 mm, 0.2756 in Closure Type Open Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 1000 lbf Static Load Capacity 550 lbf Precision Rating Class 0 Seal Type None Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 7.000 mm, 0.2756 in Outer Ring Width 0.2756 in; 7.000 mm Maximum RPM (Grease) 21000 RPM Fillet Radius 0.300 mm, 0.0118 in Maximum RPM 25000 RPM Manufacturer UPC Number 4547359006131 Weight 0.04 lbs Harmonization Code 8482.10.5048 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings 6803, D=17 Single Row Radial Ball Bearing - Open Typ SPECIFICATIONS Bore Type Round Bore Diameter 17 mm, 0.6693 in Outside Diameter 26 mm, 1.0236 in Overall Width 5 mm, 0.1969 in Closure Type Open Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 550 lbf Static Load Capacity 320 lbf Precision Rating Class 0 Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 5.000 mm, 0.1969 in Outer Ring Width 0.1969 in; 5.000 mm Maximum RPM (Grease) 24000 RPM Fillet Radius 0.300 mm, 0.0118 in Maximum RPM 28000 RPM Manufacturer UPC Number 4547359006117 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings 6800, D=10 Single Row Radial Ball Bearing - Open Type SPECIFICATIONS Bore Type Round Bore Diameter 10 mm, 0.3937 in Outside Diameter 19 mm, 0.7480 in Overall Width 5 mm, 0.1969 in Closure Type Open Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 450 lbf Static Load Capacity 200 lbf Precision Rating Class 0 Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 5.000 mm, 0.1969 in Outer Ring Width 0.1969 in; 5.000 mm Maximum RPM (Grease) 32000 RPM Fillet Radius 0.300 mm, 0.0118 in Maximum RPM 38000 RPM Manufacturer UPC Number 4547359006056 Weight 0.011 lb 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings 6414, D=70 Radial/Deep Groove Ball Bearing - Round Bore, 70 mm ID, 180 mm OD, 42 mm Width, Open, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 70.000 mm, 2.7559 in Outside Diameter 180.000 mm, 7.0866 in Overall Width 42.000 mm, 1.6535 in Closure Type Open Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 31920 lbf Static Load Capacity 20120 lbf Precision Rating Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 42.000 mm, 1.6535 in Outer Ring Width 1.6535 in; 42.000 mm Maximum RPM (Grease) 4100 RPM Maximum RPM (Oil) 4800 rpm Fillet Radius 0.1181 in, 3.000 mm Maximum RPM 4800 RPM Manufacturer UPC Number 4547359584363 Weight 11.07 lbs Harmonization Code 8482.10.5056 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings 6412, D=60 Radial/Deep Groove Ball Bearing - Round Bore, 60 mm ID, 150 mm OD, 35 mm Width, Open, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 60.000 mm, 2.3622 in Outside Diameter 150.000 mm, 5.9055 in Overall Width 35.000 mm, 1.3780 in Closure Type Open Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 25400 lbf Static Load Capacity 14500 lbf Precision Rating Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 35.000 mm, 1.3780 in Outer Ring Width 1.3780 in; 35.000 mm Maximum RPM (Grease) 4800 RPM Maximum RPM (Oil) 5700 rpm Fillet Radius 0.0827 in, 2.100 mm Maximum RPM 5700 RPM Manufacturer UPC Number 4547359584318 Weight 6.24 lbs Harmonization Code 8482.10.5056 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings 6410, D=50 Radial/Deep Groove Ball Bearing - Round Bore, 50 mm ID, 130 mm OD, 31 mm Width, Open, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 1.9685 in, 50.000 mm Outside Diameter 130.000 mm, 5.1181 in Overall Width 1.2205 in, 31.000 mm Closure Type Open Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 20680 lbf Static Load Capacity 11120 lbf Precision Rating Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 1.2205 in, 31.000 mm Outer Ring Width 1.2205 in; 31.000 mm Maximum RPM (Grease) 5700 RPM Maximum RPM (Oil) 6700 rpm Fillet Radius 0.0827 in, 2.100 mm Maximum RPM 6700 RPM Series 64 Manufacturer UPC Number 4547359405262 Weight 4.21 lbs Harmonization Code 8482.10.5056 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings 6407, D=35 Radial/Deep Groove Ball Bearing - Round Bore, 35 mm ID, 100 mm OD, 25 mm Width, Open, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 35.000 mm, 1.3780 in Outside Diameter 100.000 mm, 3.9370 in Overall Width 0.9843 in, 25.000 mm Closure Type Open Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 13710 lbf Static Load Capacity 6960 lbf Precision Rating Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 0.9843 in, 25.000 mm Outer Ring Width 0.9843 in; 25.000 mm Maximum RPM (Grease) 7800 RPM Maximum RPM (Oil) 9100 rpm Fillet Radius 0.0591 in, 1.500 mm Maximum RPM 9100 RPM Series 64 Manufacturer UPC Number 4547359584080 Weight 2.09 lbs Harmonization Code 8482.10.5052 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings 6406, D=30 Radial/Deep Groove Ball Bearing - Round Bore, 30 mm ID, 90 mm OD, 23 mm Width, Open, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 1.1811 in, 30.000 mm Outside Diameter 90.000 mm, 3.5433 in Overall Width 23.000 mm, 0.9055 in Closure Type Open Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 10790 lbf Static Load Capacity 5370 lbf Precision Rating Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 23.000 mm, 0.9055 in Outer Ring Width 0.9055 in; 23.000 mm Maximum RPM (Grease) 8800 RPM Maximum RPM (Oil) 10000 rpm Fillet Radius 0.0591 in, 1.500 mm Maximum RPM 10000 RPM Series 64 Manufacturer UPC Number 4547359405002 Weight 1.61 lbs Harmonization Code 8482.10.5052 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less