NTN

NTN6003ZZ Radial/Deep Groove Ball Bearing - Round Bore, 17 mm ID, 35 mm OD, 10 mm Width, Double Sealed, CN Internal Clearance Bore Type Round Bore Diameter 17.000 mm, 0.6693 in Outside Diameter 35.000 mm, 1.3780 in Overall Width 0.3937 in, 10.000 mm Closure Type Double Shielded Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 1690 lbf Static Load Capacity 755 lbf Precision Rating ISO Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 0.3937 in, 10.000 mm Outer Ring Width 0.3937 in; 10.000 mm Maximum RPM (Grease) 20000 RPM Fillet Radius 0.300 mm, 0.0118 in Maximum RPM 24000 RPM Series 60 Manufacturer UPC Number 4547359003680 Weight 0.08 lbs 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN6002ZZ Radial/Deep Groove Ball Bearing - Round Bore, 15 mm ID, 32 mm OD, 9 mm Width, Double Shielded, CN Internal Clearance Bore Type Round Bore Diameter 15.000 mm, 0.5906 in Outside Diameter 1.2598 in, 32.000 mm Overall Width 9.000 mm, 0.3543 in Closure Type Double Shielded Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 1390 lbf Static Load Capacity 635 lbf Precision Rating ISO Class 0 Seal Type None Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 9.000 mm, 0.3543 in Outer Ring Width 0.3543 in; 9.000 mm Maximum RPM (Grease) 22000 RPM Fillet Radius 0.300 mm, 0.0118 in Radial Dynamic Load Capacity 5600 N Radial Static Load Capacity 2830 N Manufacturer UPC Number 4547359003642 Weight 0.066 lbs 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN6001ZZ Radial/Deep Groove Ball Bearing - Round Bore, 12 mm ID, 28 mm OD, 8 mm Width, Double Shielded, CN Internal Clearance Bore Type Round Bore Diameter 0.4724 in, 12.000 mm Outside Diameter 28.000 mm, 1.1024 in Overall Width 8.000 mm, 0.3150 in Closure Type Double Shielded Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 1270 lbf Static Load Capacity 535 lbf Precision Rating ISO Class 0 Seal Type None Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 8.000 mm, 0.3150 in Outer Ring Width 0.3150 in; 8.000 mm Maximum RPM (Grease) 26000 RPM Fillet Radius 0.300 mm, 0.0118 in Radial Dynamic Load Capacity 5100 N Radial Static Load Capacity 2390 N Manufacturer UPC Number 4547359003604 Weight 0.044 lbs 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN6000ZZ Radial/Deep Groove Ball Bearing - Round Bore, 10 mm ID, 26 mm OD, 8 mm Width, Double Shielded, CN Internal Clearance Bore Type Round Bore Diameter 0.3937 in, 10.000 mm Outside Diameter 26.000 mm, 1.0236 in Overall Width 8.000 mm, 0.3150 in Closure Type Double Shielded Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 1130 lbf Static Load Capacity 440 lbf Precision Rating ISO Class 0 Seal Type None Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 8.000 mm, 0.3150 in Outer Ring Width 0.3150 in; 8.000 mm Maximum RPM (Grease) 29000 RPM Fillet Radius 0.300 mm, 0.0118 in Radial Dynamic Load Capacity 4550 N Radial Static Load Capacity 1960 N Manufacturer UPC Number 4547359003567 Weight 0.042 lbs 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings 6007, D=35  Radial/Deep Groove Ball Bearing - Round Bore, 35 mm ID, 62 mm OD, 14 mm Width, Open, CN Internal Clearance Bore Type Round Bore Diameter 35.000 mm, 1.3780 in Outside Diameter 62.000 mm, 2.4409 in Overall Width 14.000 mm, 0.5512 in Closure Type Open Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 3970 lbf Static Load Capacity 2310 lbf Precision Rating Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 14.000 mm, 0.5512 in Outer Ring Width 0.5512 in; 14.000 mm Maximum RPM (Grease) 12000 RPM Maximum RPM (Oil) 14000 rpm Fillet Radius 1.000 mm, 0.0394 in Maximum RPM 14000 RPM Weight 0.14 kg 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings 6006, D=30  Radial/Deep Groove Ball Bearing - Round Bore, 30 mm ID, 55 mm OD, 13 mm Width, Open, CN Internal Clearance Bore Type Round Bore Diameter 1.1811 in, 30.000 mm Outside Diameter 55.000 mm, 2.1654 in Overall Width 13.000 mm, 0.5118 in Closure Type Open Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 3300 lbf Static Load Capacity 1860 lbf Precision Rating Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 13.000 mm, 0.5118 in Outer Ring Width 0.5118 in; 13.000 mm Maximum RPM (Grease) 13000 RPM Maximum RPM (Oil) 15000 rpm Fillet Radius 1.000 mm, 0.0394 in Maximum RPM 15000 RPM Series 60 Weight 0.11 kg 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings 6005, D=25  Radial/Deep Groove Ball Bearing - Round Bore, 25 mm ID, 47 mm OD, 12 mm Width, Open, CN Internal Clearance Bore Type Round Bore Diameter 0.9843 in, 25.000 mm Outside Diameter 1.8504 in, 47.000 mm Overall Width 0.4724 in, 12.000 mm Closure Type Open Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 2510 lbf Static Load Capacity 1310 lbf Precision Rating Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 0.4724 in, 12.000 mm Outer Ring Width 0.4724 in; 12.000 mm Maximum RPM (Grease) 15000 RPM Maximum RPM (Oil) 18000 rpm Fillet Radius 0.600 mm, 0.0236 in Maximum RPM 18000 RPM Series 60 Weight 0.072 kg 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings 6004, D=20  Radial/Deep Groove Ball Bearing - Round Bore, 20 mm ID, 42 mm OD, 12 mm Width, Open, CN Internal Clearance Bore Type Round Bore Diameter 20.000 mm, 0.7874 in Outside Diameter 42.000 mm, 1.6535 in Overall Width 0.4724 in, 12.000 mm Closure Type Open Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 2330 lbf Static Load Capacity 1130 lbf Precision Rating Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 0.4724 in, 12.000 mm Outer Ring Width 0.4724 in; 12.000 mm Maximum RPM (Grease) 18000 RPM Maximum RPM (Oil) 21000 rpm Fillet Radius 0.600 mm, 0.0236 in Maximum RPM 21000 RPM Series 60 Weight 0.068 kg 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings 6003, D=17  Radial/Deep Groove Ball Bearing - Round Bore, 17 mm ID, 35 mm OD, 10 mm Width, Open, CN Internal Clearance Bore Type Round Bore Diameter 17.000 mm, 0.6693 in Outside Diameter 35.000 mm, 1.3780 in Overall Width 0.3937 in, 10.000 mm Closure Type Open Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 1690 lbf Static Load Capacity 750 lbf Precision Rating Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 0.3937 in, 10.000 mm Outer Ring Width 0.3937 in; 10.000 mm Maximum RPM (Grease) 20000 RPM Maximum RPM (Oil) 24000 rpm Fillet Radius 0.300 mm, 0.0118 in Maximum RPM 24000 RPM Weight 0.036 kg 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings 6002, D=15  Radial/Deep Groove Ball Bearing - Round Bore, 15 mm ID, 32 mm OD, 9 mm Width, Double Sealed, CN Internal Clearance Bore Type Round Bore Diameter 15.000 mm, 0.5906 in Outside Diameter 1.2598 in, 32.000 mm Overall Width 9.000 mm, 0.3543 in Closure Type Open Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 1390 lbf Static Load Capacity 630 lbf Precision Rating Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 9.000 mm, 0.3543 in Outer Ring Width 0.3543 in; 9.000 mm Maximum RPM (Grease) 22000 RPM Maximum RPM (Oil) 26000 rpm Fillet Radius 0.300 mm, 0.0118 in Maximum RPM 26000 RPM Series 60 Weight 0.031 kg 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings 6001, D=12  Radial/Deep Groove Ball Bearing - Round Bore, 12 mm ID, 28 mm OD, 8 mm Width, Open, CN Internal Clearance Bore Type Round Bore Diameter 0.4724 in, 12.000 mm Outside Diameter 28.000 mm, 1.1024 in Overall Width 8.000 mm, 0.3150 in Closure Type Open Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 1270 lbf Static Load Capacity 530 lbf Precision Rating Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 8.000 mm, 0.3150 in Outer Ring Width 0.3150 in; 8.000 mm Maximum RPM (Grease) 26000 RPM Maximum RPM (Oil) 30000 rpm Fillet Radius 0.300 mm, 0.0118 in Maximum RPM 30000 RPM Weight 0.05 lbs 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings 6000 ,Single-Row D=10 Radial/Deep Groove Ball Bearing - Round Bore, 10 mm ID, 26 mm OD, 8 mm Width, Open, CN Internal Clearance Bore Type Round Bore Diameter 0.3937 in, 10.000 mm Outside Diameter 26.000 mm, 1.0236 in Overall Width 8.000 mm, 0.3150 in Closure Type Open Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 1130 lbf Static Load Capacity 440 lbf Precision Rating Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 8.000 mm, 0.3150 in Outer Ring Width 0.3150 in; 8.000 mm Maximum RPM (Grease) 29000 RPM Maximum RPM (Oil) 34000 rpm Fillet Radius 0.300 mm, 0.0118 in Maximum RPM 34000 RPM Weight 0.018 kg 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 6906 1.1811 in 30.000 mm 1.8504 in 47.000 mm 0.3543 in 9.000 mm 0.0118 in 0.300 mm 1120 lbf 5000 N 5.00 kN 1790 lbf 8000 N 8.00 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 6904 0.7874 in 20.000 mm 1.4567 in 37.000 mm 0.3543 in 9.000 mm 0.0118 in 0.300 mm 830 lbf 3700 N 3.70 kN 1580 lbf 7050 N 7.05 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 6903 0.6693 in 17.000 mm 1.1811 in 30.000 mm 0.2756 in 7.000 mm 0.0118 in 0.300 mm 580 lbf 2580 N 2.58 kN 1150 lbf 5150 N 5.15 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 6902 0.5906 in 15.000 mm 1.1024 in 28.000 mm 0.2756 in 7.000 mm 0.0118 in 0.300 mm 440 lbf 2000 N 2.00 kN 910 lbf 4050 N 4.05 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 6900 0.3937 in 10.000 mm 0.8661 in 22.000 mm 0.2362 in 6.000 mm 0.0118 in 0.300 mm 280 lbf 1270 N 1.27 kN 670 lbf 2990 N 2.99 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 6830 5.9055 in 150.000 mm 7.4803 in 190.000 mm 0.7874 in 20.000 mm 0.0433 in 1.100 mm 12360 lbf 55000 N 55.00 kN 11910 lbf 53000 N 53.00 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 6826 5.1181 in 130.000 mm 6.4961 in 165.000 mm 0.7087 in 18.000 mm 0.0433 in 1.100 mm 9210 lbf 41000 N 41.00 kN 9210 lbf 41000 N 41.00 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 6824 4.7244 in 120.000 mm 5.9055 in 150.000 mm 0.6299 in 16.000 mm 0.0394 in 1.000 mm 7410 lbf 33000 N 33.00 kN 7190 lbf 32000 N 32.00 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 6822 4.3307 in 110.000 mm 5.5118 in 140.000 mm 0.6299 in 16.000 mm 0.0394 in 1.000 mm 6330 lbf 28200 N 28.20 kN 6180 lbf 27500 N 27.50 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 6821 4.1339 in 105.000 mm 5.1181 in 130.000 mm 0.5118 in 13.000 mm 0.0394 in 1.000 mm 4940 lbf 22000 N 22.00 kN 4940 lbf 22000 N 22.00 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 6820 3.9370 in 100.000 mm 4.9213 in 125.000 mm 0.5118 in 13.000 mm 0.0394 in 1.000 mm 4760 lbf 21200 N 21.20 kN 4870 lbf 21700 N 21.70 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 6819 3.7402 in 95.000 mm 4.7244 in 120.000 mm 0.5118 in 13.000 mm 0.0394 in 1.000 mm 4600 lbf 20500 N 20.50 kN 4810 lbf 21400 N 21.40 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 6818 3.5433 in 90.000 mm 4.5276 in 115.000 mm 0.5118 in 13.000 mm 0.0394 in 1.000 mm 4420 lbf 19700 N 19.70 kN 4740 lbf 21100 N 21.10 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 6817 3.3465 in 85.000 mm 4.3307 in 110.000 mm 0.5118 in 13.000 mm 0.0394 in 1.000 mm 4270 lbf 19000 N 19.00 kN 4650 lbf 20700 N 20.70 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 6815 2.9528 in 75.000 mm 3.7402 in 95.000 mm 0.3937 in 10.000 mm 0.0236 in 0.600 mm 2900 lbf 12900 N 12.90 kN 3120 lbf 13900 N 13.90 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 6814 2.7559 in 70.000 mm 3.5433 in 90.000 mm 0.3937 in 10.000 mm 0.0236 in 0.600 mm 2670 lbf 11900 N 11.90 kN 3010 lbf 13400 N 13.40 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 6812 2.3622 in 60.000 mm 3.0709 in 78.000 mm 0.3937 in 10.000 mm 0.0118 in 0.300 mm 2380 lbf 10600 N 10.60 kN 2850 lbf 12700 N 12.70 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 6811 2.1654 in 55.000 mm 2.8346 in 72.000 mm 0.3543 in 9.000 mm 0.0118 in 0.300 mm 1820 lbf 8100 N 8.10 kN 2190 lbf 9750 N 9.75 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 6810 1.9685 in 50.000 mm 2.5591 in 65.000 mm 0.2756 in 7.000 mm 0.0118 in 0.300 mm 1370 lbf 6100 N 6.10 kN 1640 lbf 7300 N 7.30 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 6809 1.7717 in 45.000 mm 2.2835 in 58.000 mm 0.2756 in 7.000 mm 0.0118 in 0.300 mm 1110 lbf 4950 N 4.95 kN 1330 lbf 5950 N 5.95 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 6807 1.3780 in 35.000 mm 1.8504 in 47.000 mm 0.2756 in 7.000 mm 0.0118 in 0.300 mm 910 lbf 4050 N 4.05 kN 1220 lbf 5450 N 5.45 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 6806 1.1811 in 30.000 mm 1.6535 in 42.000 mm 0.2756 in 7.000 mm 0.0118 in 0.300 mm 820 lbf 3650 N 3.65 kN 1160 lbf 5200 N 5.20 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 6805 0.9843 in 25.000 mm 1.4567 in 37.000 mm 0.2756 in 7.000 mm 0.0118 in 0.300 mm 660 lbf 2950 N 2.95 kN 1060 lbf 4750 N 4.75 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 6802 0.5906 in 15.000 mm 0.9449 in 24.000 mm 0.1969 in 5.000 mm 0.0118 in 0.300 mm 280 lbf 1260 N 1.26 kN 510 lbf 2300 N 2.30 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 6801 0.4724 in 12.000 mm 0.8268 in 21.000 mm 0.1969 in 5.000 mm 0.0118 in 0.300 mm 230 lbf 1040 N 1.04 kN 470 lbf 2120 N 2.12 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 6418 3.5433 in 90.000 mm 8.8583 in 225.000 mm 2.1260 in 54.000 mm 0.1181 in 3.000 mm 33500 lbf 149000 N 149.00 kN 41500 lbf 184000 N 184.00 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 6417 3.3465 in 85.000 mm 8.2677 in 210.000 mm 2.0472 in 52.000 mm 0.1181 in 3.000 mm 28800 lbf 128000 N 128.00 kN 37000 lbf 165000 N 165.00 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 6416 3.1496 in 80.000 mm 7.8740 in 200.000 mm 1.8898 in 48.000 mm 0.1181 in 3.000 mm 28100 lbf 125000 N 125.00 kN 40690 lbf 181000 N 181.00 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 6415 2.9528 in 75.000 mm 7.4803 in 190.000 mm 1.7717 in 45.000 mm 0.1181 in 3.000 mm 22250 lbf 99000 N 99.00 kN 34170 lbf 152000 N 152.00 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 6413 2.5591 in 65.000 mm 6.2992 in 160.000 mm 1.4567 in 37.000 mm 0.0827 in 2.100 mm 16290 lbf 72500 N 72.50 kN 27650 lbf 123000 N 123.00 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 6411 2.1654 in 55.000 mm 5.5118 in 140.000 mm 1.2992 in 33.000 mm 0.0827 in 2.100 mm 12130 lbf 54000 N 54.00 kN 22140 lbf 98500 N 98.50 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 6409 1.7717 in 45.000 mm 4.7244 in 120.000 mm 1.1417 in 29.000 mm 0.0787 in 2.000 mm 10110 lbf 45000 N 45.00 kN 19220 lbf 85500 N 85.50 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 6408 1.5748 in 40.000 mm 4.3307 in 110.000 mm 1.0630 in 27.000 mm 0.0787 in 2.000 mm 8200 lbf 36500 N 36.50 kN 15840 lbf 70500 N 70.50 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 6405 0.9843 in 25.000 mm 3.1496 in 80.000 mm 0.8268 in 21.000 mm 0.0591 in 1.500 mm 3930 lbf 17500 N 17.50 kN 8650 lbf 38500 N 38.50 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 6404 0.7874 in 20.000 mm 2.8346 in 72.000 mm 0.7480 in 19.000 mm 0.0433 in 1.100 mm 3120 lbf 13900 N 13.90 kN 7080 lbf 31500 N 31.50 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

Item # d D B r Static Load Rating Dynamic Load Rating 6403 0.6693 in 17.000 mm 2.4409 in 62.000 mm 0.6693 in 17.000 mm 0.0433 in 1.100 mm 2420 lbf 10800 N 10.80 kN 5660 lbf 25200 N 25.20 kN 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less