NTN

NTN Deep Groove Ball Bearings  6213ZZC3, D=65 Radial/Deep Groove Ball Bearing - Round Bore, 65 mm ID, 120 mm OD, 23 mm Width, Double Shielded, C3 Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 65 mm Outside Diameter 120 mm Overall Width 23 mm Closure Type Double Shielded Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance C3 Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 14270 lbf Static Load Capacity 9000 lbf Precision Rating ISO Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 23.000 mm, 0.9055 in Outer Ring Width 0.9055 in; 23.000 mm Maximum RPM (Grease) 5500 RPM Fillet Radius 0.0591 in, 1.500 mm Manufacturer UPC Number 4547359568899 Weight 2.16 lbs Harmonization Code 8482.10.5056 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6213ZZ, D=65 Radial/Deep Groove Ball Bearing - Round Bore, 65 mm ID, 120 mm OD, 23 mm Width, Double Shielded, C3 Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 65 mm Outside Diameter 120 mm Overall Width 23 mm Closure Type Double Shielded Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance C3 Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 14270 lbf Static Load Capacity 9000 lbf Precision Rating ISO Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 23.000 mm, 0.9055 in Outer Ring Width 0.9055 in; 23.000 mm Maximum RPM (Grease) 5500 RPM Fillet Radius 0.0591 in, 1.500 mm Manufacturer UPC Number 4547359568899 Weight 2.16 lbs Harmonization Code 8482.10.5056 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6211ZZC3, D=55 Radial/Deep Groove Ball Bearing - Round Bore, 55 mm ID, 100 mm OD, 21 mm Width, Double Shielded, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 55 mm Outside Diameter 100 mm Overall Width 21 mm Closure Type Double Shielded Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 10790 lbf Static Load Capacity 6550 lbf Precision Rating ISO Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 0.8268 in, 21.000 mm Outer Ring Width 0.8268 in; 21.000 mm Maximum RPM (Grease) 6400 RPM Fillet Radius 0.0591 in, 1.500 mm Maximum RPM 7600 RPM Series 62 Manufacturer UPC Number 4547359004847 Weight 1.34 lbs Harmonization Code 8482.10.5052 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6211ZZ, D=55 Radial/Deep Groove Ball Bearing - Round Bore, 55 mm ID, 100 mm OD, 21 mm Width, Double Shielded, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 55 mm Outside Diameter 100 mm Overall Width 21 mm Closure Type Double Shielded Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 10790 lbf Static Load Capacity 6550 lbf Precision Rating ISO Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 0.8268 in, 21.000 mm Outer Ring Width 0.8268 in; 21.000 mm Maximum RPM (Grease) 6400 RPM Fillet Radius 0.0591 in, 1.500 mm Maximum RPM 7600 RPM Series 62 Manufacturer UPC Number 4547359004847 Weight 1.34 lbs Harmonization Code 8482.10.5052 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6210ZZ, D=50 Radial/Deep Groove Ball Bearing - Round Bore, 50 mm ID, 90 mm OD, 20 mm Width, Double Shielded, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 50 mm Outside Diameter 90 mm Overall Width 20 mm Closure Type Double Shielded Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 8760 lbf Static Load Capacity 5200 lbf Precision Rating ISO Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 20.000 mm, 0.7874 in Outer Ring Width 0.7874 in; 20.000 mm Maximum RPM (Grease) 7100 RPM Fillet Radius 1.100 mm, 0.0433 in Manufacturer UPC Number 4547359004809 Weight 1.00 lbs Harmonization Code 8482.10.5052 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6209ZZ, D=45 Radial/Deep Groove Ball Bearing - Round Bore, 45 mm ID, 85 mm OD, 19 mm Width, Double Shielded, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 45 mm Outside Diameter 85 mm Overall Width 19 mm Closure Type Double Shielded Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 8090 lbf Static Load Capacity 4600 lbf Precision Rating ISO Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 19.000 mm, 0.7480 in Outer Ring Width 0.7480 in; 19.000 mm Maximum RPM (Grease) 7800 RPM Fillet Radius 1.100 mm, 0.0433 in Maximum RPM 9200 RPM Series 62 Manufacturer UPC Number 4547359004762 Weight 0.88 lbs Harmonization Code 8482.10.5052 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6208ZZ, D=40 Radial/Deep Groove Ball Bearing - Round Bore, 40 mm ID, 80 mm OD, 18 mm Width, Double Shielded, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 40 mm Outside Diameter 80 mm Overall Width 18 mm Closure Type Double Shielded Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 7300 lbf Static Load Capacity 4000 lbf Precision Rating ISO Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 18.000 mm, 0.7087 in Outer Ring Width 0.7087 in; 18.000 mm Maximum RPM (Grease) 8700 RPM Fillet Radius 1.100 mm, 0.0433 in Maximum RPM 10000 RPM Series 62 Manufacturer UPC Number 4547359004724 Weight 0.811 lbs Harmonization Code 8482.10.5052 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6207ZZC3, D=35 Radial/Deep Groove Ball Bearing - Round Bore, 35 mm ID, 72 mm OD, 17 mm Width, Double Shielded, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 35 mm Outside Diameter 72 mm Overall Width 17 mm Closure Type Double Shielded Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 6380 lbf Static Load Capacity 3450 lbf Precision Rating ISO Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 17.000 mm, 0.6693 in Outer Ring Width 0.6693 in; 17.000 mm Maximum RPM (Grease) 9800 RPM Fillet Radius 1.100 mm, 0.0433 in Maximum RPM 11000 RPM Series 62 Manufacturer UPC Number 4547359004687 Weight 0.626 lbs Harmonization Code 8482.10.5052 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6207ZZ, D=35 Radial/Deep Groove Ball Bearing - Round Bore, 35 mm ID, 72 mm OD, 17 mm Width, Double Shielded, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 35 mm Outside Diameter 72 mm Overall Width 17 mm Closure Type Double Shielded Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 6380 lbf Static Load Capacity 3450 lbf Precision Rating ISO Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 17.000 mm, 0.6693 in Outer Ring Width 0.6693 in; 17.000 mm Maximum RPM (Grease) 9800 RPM Fillet Radius 1.100 mm, 0.0433 in Maximum RPM 11000 RPM Series 62 Manufacturer UPC Number 4547359004687 Weight 0.626 lbs Harmonization Code 8482.10.5052 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6206ZZC3, D=30 Radial/Deep Groove Ball Bearing - Round Bore, 30 mm ID, 62 mm OD, 16 mm Width, Double Sealed, C3 Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 30 mm Outside Diameter 62 mm Overall Width 16 mm Closure Type Double Shielded Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance C3 Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 4850 lbf Static Load Capacity 2540 lbf Precision Rating ISO Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 16.000 mm, 0.6299 in Outer Ring Width 0.6299 in; 16.000 mm Maximum RPM (Grease) 11000 RPM Fillet Radius 1.000 mm, 0.0394 in Maximum RPM 7300 RPM Series 62 Manufacturer UPC Number 4547359564792 Weight 0.44 lbs Harmonization Code 8482.10.5052 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6205ZZC3, D=25 Radial/Deep Groove Ball Bearing - Round Bore, 25 mm ID, 52 mm OD, 15 mm Width, Double Shielded, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 25 mm Outside Diameter 52 mm Overall Width 15 mm Closure Type Double Shielded Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 3480 lbf Static Load Capacity 1760 lbf Precision Rating ISO Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 15.000 mm, 0.5906 in Outer Ring Width 0.5906 in; 15.000 mm Maximum RPM (Grease) 13000 RPM Fillet Radius 1.000 mm, 0.0394 in Manufacturer UPC Number 4547359004601 Weight 0.28 lbs Harmonization Code 8482.10.5048 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6205ZZ, D=25 Radial/Deep Groove Ball Bearing - Round Bore, 25 mm ID, 52 mm OD, 15 mm Width, Double Shielded, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 25 mm Outside Diameter 52 mm Overall Width 15 mm Closure Type Double Shielded Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 3480 lbf Static Load Capacity 1760 lbf Precision Rating ISO Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 15.000 mm, 0.5906 in Outer Ring Width 0.5906 in; 15.000 mm Maximum RPM (Grease) 13000 RPM Fillet Radius 1.000 mm, 0.0394 in Manufacturer UPC Number 4547359004601 Weight 0.28 lbs Harmonization Code 8482.10.5048 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6204ZZC3, D=20 Radial/Deep Groove Ball Bearing - Round Bore, 20 mm ID, 47 mm OD, 14 mm Width, Double Shielded, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 20 mm Outside Diameter 47 mm Overall Width 14 mm Closure Type Double Shielded Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 3190 lbf Static Load Capacity 1500 lbf Precision Rating ISO Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 14.000 mm, 0.5512 in Outer Ring Width 0.5512 in; 14.000 mm Maximum RPM (Grease) 16000 RPM Fillet Radius 1.000 mm, 0.0394 in Maximum RPM 18000 RPM Series 62 Manufacturer UPC Number 4547359004564 Weight 0.23 lbs Harmonization Code 8482.10.5048 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6204ZZ, D=20 Radial/Deep Groove Ball Bearing - Round Bore, 20 mm ID, 47 mm OD, 14 mm Width, Double Shielded, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 20 mm Outside Diameter 47 mm Overall Width 14 mm Closure Type Double Shielded Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 3190 lbf Static Load Capacity 1500 lbf Precision Rating ISO Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 14.000 mm, 0.5512 in Outer Ring Width 0.5512 in; 14.000 mm Maximum RPM (Grease) 16000 RPM Fillet Radius 1.000 mm, 0.0394 in Maximum RPM 18000 RPM Series 62 Manufacturer UPC Number 4547359004564 Weight 0.23 lbs Harmonization Code 8482.10.5048 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6203ZZC3, D=17 Radial/Deep Groove Ball Bearing - Round Bore, 15 mm ID, 35 mm OD, 11 mm Width, Double Shielded, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 15 mm Outside Diameter 35 mm Overall Width 11 mm Closure Type Double Shielded Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 1930 lbf Static Load Capacity 810 lbf Precision Rating ISO Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 11.000 mm, 0.4331 in Outer Ring Width 0.4331 in; 11.000 mm Maximum RPM (Grease) 19000 RPM Fillet Radius 0.600 mm, 0.0236 in Manufacturer UPC Number 4547359004489 Weight 0.09 lbs Harmonization Code 8482.10.5048 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6203ZZ, D=17 Radial/Deep Groove Ball Bearing - Round Bore, 15 mm ID, 35 mm OD, 11 mm Width, Double Shielded, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 15 mm Outside Diameter 35 mm Overall Width 11 mm Closure Type Double Shielded Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 1930 lbf Static Load Capacity 810 lbf Precision Rating ISO Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 11.000 mm, 0.4331 in Outer Ring Width 0.4331 in; 11.000 mm Maximum RPM (Grease) 19000 RPM Fillet Radius 0.600 mm, 0.0236 in Manufacturer UPC Number 4547359004489 Weight 0.09 lbs Harmonization Code 8482.10.5048 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6202ZZC3, D=15 Radial/Deep Groove Ball Bearing - Round Bore, 15 mm ID, 35 mm OD, 11 mm Width, Double Shielded, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 15 mm Outside Diameter 35 mm Overall Width 11 mm Closure Type Double Shielded Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 1930 lbf Static Load Capacity 810 lbf Precision Rating ISO Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 11.000 mm, 0.4331 in Outer Ring Width 0.4331 in; 11.000 mm Maximum RPM (Grease) 19000 RPM Fillet Radius 0.600 mm, 0.0236 in Manufacturer UPC Number 4547359004489 Weight 0.09 lbs Harmonization Code 8482.10.5048 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6202ZZ, D=15 Radial/Deep Groove Ball Bearing - Round Bore, 15 mm ID, 35 mm OD, 11 mm Width, Double Shielded, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 15 mm Outside Diameter 35 mm Overall Width 11 mm Closure Type Double Shielded Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 1930 lbf Static Load Capacity 810 lbf Precision Rating ISO Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 11.000 mm, 0.4331 in Outer Ring Width 0.4331 in; 11.000 mm Maximum RPM (Grease) 19000 RPM Fillet Radius 0.600 mm, 0.0236 in Manufacturer UPC Number 4547359004489 Weight 0.09 lbs Harmonization Code 8482.10.5048 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6201ZZC3, D=12 Radial/Deep Groove Ball Bearing - Round Bore, 12 mm ID, 32 mm OD, 10 mm Width, Double Shielded, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 12 mm Outside Diameter 32 mm Overall Width 10 mm Closure Type Double Shielded Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 1510 lbf Static Load Capacity 620 lbf Precision Rating ISO Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 0.3937 in, 10.000 mm Outer Ring Width 0.3937 in; 10.000 mm Maximum RPM (Grease) 22000 RPM Fillet Radius 0.600 mm, 0.0236 in Manufacturer UPC Number 4547359004441 Weight 0.08 lbs Harmonization Code 8482.10.5048 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6201ZZ, D=12 Radial/Deep Groove Ball Bearing - Round Bore, 12 mm ID, 32 mm OD, 10 mm Width, Double Shielded, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 12 mm Outside Diameter 32 mm Overall Width 10 mm Closure Type Double Shielded Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 1510 lbf Static Load Capacity 620 lbf Precision Rating ISO Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 0.3937 in, 10.000 mm Outer Ring Width 0.3937 in; 10.000 mm Maximum RPM (Grease) 22000 RPM Fillet Radius 0.600 mm, 0.0236 in Manufacturer UPC Number 4547359004441 Weight 0.08 lbs Harmonization Code 8482.10.5048 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6200ZZC3, D=10 Radial/Deep Groove Ball Bearing - Round Bore, 10 mm ID, 30 mm OD, 9 mm Width, Double Shielded, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 10 mm Outside Diameter 30 mm Overall Width 9 mm Closure Type Double Shielded Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 1270 lbf Static Load Capacity 535 lbf Precision Rating ISO Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 9.000 mm, 0.3543 in Outer Ring Width 0.3543 in; 9.000 mm Maximum RPM (Grease) 25000 RPM Fillet Radius 0.600 mm, 0.0236 in Manufacturer UPC Number 4547359004403 Weight 0.07 lbs Harmonization Code 8482.10.5044 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6200ZZ, D=10 Radial/Deep Groove Ball Bearing - Round Bore, 10 mm ID, 30 mm OD, 9 mm Width, Double Shielded, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 10 mm Outside Diameter 30 mm Overall Width 9 mm Closure Type Double Shielded Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 1270 lbf Static Load Capacity 535 lbf Precision Rating ISO Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 9.000 mm, 0.3543 in Outer Ring Width 0.3543 in; 9.000 mm Maximum RPM (Grease) 25000 RPM Fillet Radius 0.600 mm, 0.0236 in Manufacturer UPC Number 4547359004403 Weight 0.07 lbs Harmonization Code 8482.10.5044 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6032ZZ, D=160 Radial/Deep Groove Ball Bearing - Round Bore, 160 mm ID, 240 mm OD, 38 mm Width, Double Shielded, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 160 mm Outside Diameter 240 mm Overall Width 38 mm Closure Type Double Shielded Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 35510 lbf Static Load Capacity 28300 lbf Precision Rating ISO Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 38.000 mm, 1.4961 in Outer Ring Width 1.4961 in; 38.000 mm Maximum RPM (Grease) 2800 RPM Fillet Radius 0.0827 in, 2.100 mm Maximum RPM 3000 RPM Series 60 Manufacturer UPC Number 4547359551495 Weight 11.55 lbs Harmonization Code 8482.10.5056 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6030ZZC3, D=150 Single Row Radial Ball Bearing - Double Shielded SPECIFICATIONS Bore Type Round Bore Diameter 150 mm Outside Diameter 225 mm Overall Width 35 mm Closure Type Double Shielded Internal Clearance C3 Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 31240 lbf Static Load Capacity 28300 lbf Precision Rating ISO Class 0 Seal Type None Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 35.000 mm, 1.3780 in Outer Ring Width 1.3780 in; 35.000 mm Maximum RPM (Grease) 2800 RPM Fillet Radius 0.0827 in, 2.100 mm Manufacturer UPC Number 4547359551471 Harmonization Code 8482.10.5056 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6026ZZC3, D=130 Radial/Deep Groove Ball Bearing - Round Bore, 130 mm ID, 200 mm OD, 33 mm Width, Double Shielded, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 130 mm Outside Diameter 200 mm Overall Width 33 mm Closure Type Double Shielded Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 26520 lbf Static Load Capacity 22700 lbf Precision Rating ISO Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 33.000 mm, 1.2992 in Outer Ring Width 1.2992 in; 33.000 mm Maximum RPM (Grease) 3200 RPM Fillet Radius 2.000 mm, 0.0787 in Maximum RPM 3800 RPM Series 60 Manufacturer UPC Number 4547359551341 Weight 7.21 lbs Harmonization Code 8482.10.5056 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6024ZZC3, D=120 Radial/Deep Groove Ball Bearing - Round Bore, 120 mm ID, 180 mm OD, 28 mm Width, Double Sealed, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 120 mm Outside Diameter 180 mm Overall Width 28 mm Closure Type Double Shielded Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 21130 lbf Static Load Capacity 17900 lbf Precision Rating ISO Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 28.000 mm, 1.1024 in Outer Ring Width 1.1024 in; 28.000 mm Maximum RPM (Grease) 3500 RPM Fillet Radius 2.000 mm, 0.0787 in Maximum RPM 4100 RPM Series 60 Manufacturer UPC Number 4547359756142 Weight 4.70 lbs Harmonization Code 8482.10.5056 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6024ZZ, D=120 Radial/Deep Groove Ball Bearing - Round Bore, 120 mm ID, 180 mm OD, 28 mm Width, Double Sealed, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 120 mm Outside Diameter 180 mm Overall Width 28 mm Closure Type Double Shielded Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 21130 lbf Static Load Capacity 17900 lbf Precision Rating ISO Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 28.000 mm, 1.1024 in Outer Ring Width 1.1024 in; 28.000 mm Maximum RPM (Grease) 3500 RPM Fillet Radius 2.000 mm, 0.0787 in Maximum RPM 4100 RPM Series 60 Manufacturer UPC Number 4547359756142 Weight 4.70 lbs Harmonization Code 8482.10.5056 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6021ZZC3, D=105 Radial/Deep Groove Ball Bearing - Round Bore, 105 mm ID, 160 mm OD, 26 mm Width, Double Shielded, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 105 mm Outside Diameter 160 mm Overall Width 26 mm Closure Type Double Shielded Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 18090 lbf Static Load Capacity 14700 lbf Precision Rating ISO Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 26.000 mm, 1.0236 in Outer Ring Width 1.0236 in; 26.000 mm Maximum RPM (Grease) 4000 RPM Fillet Radius 2.000 mm, 0.0787 in Manufacturer UPC Number 4547359337211 Weight 3.527 lbs Harmonization Code 8482.10.5056 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6021ZZ, D=105 Radial/Deep Groove Ball Bearing - Round Bore, 105 mm ID, 160 mm OD, 26 mm Width, Double Shielded, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 105 mm Outside Diameter 160 mm Overall Width 26 mm Closure Type Double Shielded Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 18090 lbf Static Load Capacity 14700 lbf Precision Rating ISO Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 26.000 mm, 1.0236 in Outer Ring Width 1.0236 in; 26.000 mm Maximum RPM (Grease) 4000 RPM Fillet Radius 2.000 mm, 0.0787 in Manufacturer UPC Number 4547359337211 Weight 3.527 lbs Harmonization Code 8482.10.5056 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6020ZZC3, D=100 Radial/Deep Groove Ball Bearing - Cylindrical, 100.000 mm Bore, 150.000 mm OD, 24.000 mm Width, Metal Shield - Both Sides, C3 Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 100 mm Outside Diameter 150 mm Overall Width 24 mm Closure Type Double Shielded Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance C3 Operating Temperature Range -40 ºF to 250 ºF Cage Type Pressed - Riveted Dynamic Load Capacity 14940 lbf Static Load Capacity 12100 lbf Precision Rating RBEC-1, ISO-Normal, ABEC-1, JIS-0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 24.000 mm, 0.9449 in Outer Ring Width 0.9449 in; 24.000 mm Maximum RPM (Grease) 4200 RPM Fillet Radius 0.0591 in, 1.500 mm Manufacturer UPC Number 4547359010480 Weight 2.79 lbs 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6019ZZC3, D=95 Single Row Radial Ball Bearing - Double Shielded SPECIFICATIONS Bore Type Round Bore Diameter 95 mm Outside Diameter 145 mm Overall Width 24 mm Closure Type Double Shielded Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 15060 lbf Static Load Capacity 12100 lbf Precision Rating ISO Class 0 Seal Type None Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 24.000 mm, 0.9449 in Outer Ring Width 0.9449 in; 24.000 mm Maximum RPM (Grease) 4500 RPM Fillet Radius 0.0591 in, 1.500 mm Manufacturer UPC Number 4547359004328 Weight 2.69 lb 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6019ZZ, D=95 Single Row Radial Ball Bearing - Double Shielded SPECIFICATIONS Bore Type Round Bore Diameter 95 mm Outside Diameter 145 mm Overall Width 24 mm Closure Type Double Shielded Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 15060 lbf Static Load Capacity 12100 lbf Precision Rating ISO Class 0 Seal Type None Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 24.000 mm, 0.9449 in Outer Ring Width 0.9449 in; 24.000 mm Maximum RPM (Grease) 4500 RPM Fillet Radius 0.0591 in, 1.500 mm Manufacturer UPC Number 4547359004328 Weight 2.69 lb 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6018ZZ, D=90 Radial/Deep Groove Ball Bearing - Round Bore, 90 mm ID, 140 mm OD, 24 mm Width, Double Shielded, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 90 mm Outside Diameter 140 mm Overall Width 24 mm Closure Type Double Shielded Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 14500 lbf Static Load Capacity 11100 lbf Precision Rating ISO Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 24.000 mm, 0.9449 in Outer Ring Width 0.9449 in; 24.000 mm Maximum RPM (Grease) 4700 RPM Fillet Radius 0.0591 in, 1.500 mm Weight 2.579 lbs Harmonization Code 8482.10.5056 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6017ZZC3, D=85 Radial/Deep Groove Ball Bearing - Round Bore, 85 mm ID, 130 mm OD, 22 mm Width, Double Shielded, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 85 mm Outside Diameter 130 mm Overall Width 22 mm Closure Type Double Shielded Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 12360 lbf Static Load Capacity 9650 lbf Precision Rating ISO Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 0.8661 in, 22.000 mm Outer Ring Width 0.8661 in; 22.000 mm Maximum RPM (Grease) 5000 RPM Fillet Radius 1.100 mm, 0.0433 in Manufacturer UPC Number 4547359004243 Weight 1.997 lbs Harmonization Code 8482.10.5056 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6017ZZ, D=85 Radial/Deep Groove Ball Bearing - Round Bore, 85 mm ID, 130 mm OD, 22 mm Width, Double Shielded, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 85 mm Outside Diameter 130 mm Overall Width 22 mm Closure Type Double Shielded Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 12360 lbf Static Load Capacity 9650 lbf Precision Rating ISO Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 0.8661 in, 22.000 mm Outer Ring Width 0.8661 in; 22.000 mm Maximum RPM (Grease) 5000 RPM Fillet Radius 1.100 mm, 0.0433 in Manufacturer UPC Number 4547359004243 Weight 1.997 lbs Harmonization Code 8482.10.5056 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6016ZZC3, D=80 Radial/Deep Groove Ball Bearing - Round Bore, 70 mm ID, 110 mm OD, 20 mm Width, Double Shielded, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 80 mm Outside Diameter 125 mm Overall Width 22 mm Closure Type Double Shielded Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 11910 lbf Static Load Capacity 9000 lbf Precision Rating ISO Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 0.8661 in, 22.000 mm Outer Ring Width 0.8661 in; 22.000 mm Maximum RPM (Grease) 5300 RPM Fillet Radius 1.100 mm, 0.0433 in Manufacturer UPC Number 4547359004205 Weight 1.89 lbs Harmonization Code 8482.10.5056 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6016ZZ, D=80 Radial/Deep Groove Ball Bearing - Round Bore, 80 mm ID, 125 mm OD, 22 mm Width, Double Shielded, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 80 mm Outside Diameter 125 mm Overall Width 22 mm Closure Type Double Shielded Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 11910 lbf Static Load Capacity 9000 lbf Precision Rating ISO Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 0.8661 in, 22.000 mm Outer Ring Width 0.8661 in; 22.000 mm Maximum RPM (Grease) 5300 RPM Fillet Radius 1.100 mm, 0.0433 in Manufacturer UPC Number 4547359004205 Weight 1.89 lbs Harmonization Code 8482.10.5056 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6015ZZC3, D=75 Radial/Deep Groove Ball Bearing - Round Bore, 70 mm ID, 110 mm OD, 20 mm Width, Double Shielded, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 75 mm Outside Diameter 115 mm Overall Width 20 mm Closure Type Double Shielded Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 9890 lbf Static Load Capacity 7550 lbf Precision Rating ISO Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 20.000 mm, 0.7874 in Outer Ring Width 0.7874 in; 20.000 mm Maximum RPM (Grease) 5700 RPM Fillet Radius 1.100 mm, 0.0433 in Maximum RPM 6700 RPM Series 60 Manufacturer UPC Number 4547359004168 Weight 1.43 lbs Harmonization Code 8482.10.5056 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6015ZZ, D=75 Radial/Deep Groove Ball Bearing - Round Bore, 70 mm ID, 110 mm OD, 20 mm Width, Double Shielded, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 75 mm Outside Diameter 115 mm Overall Width 20 mm Closure Type Double Shielded Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 9890 lbf Static Load Capacity 7550 lbf Precision Rating ISO Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 20.000 mm, 0.7874 in Outer Ring Width 0.7874 in; 20.000 mm Maximum RPM (Grease) 5700 RPM Fillet Radius 1.100 mm, 0.0433 in Maximum RPM 6700 RPM Series 60 Manufacturer UPC Number 4547359004168 Weight 1.43 lbs Harmonization Code 8482.10.5056 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6014ZZC3, D=70 Radial/Deep Groove Ball Bearing - Round Bore, 70 mm ID, 110 mm OD, 20 mm Width, Double Shielded, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 70 mm Outside Diameter 110 mm Overall Width 20 mm Closure Type Double Shielded Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 9440 lbf Static Load Capacity 6950 lbf Precision Rating ISO Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 20.000 mm, 0.7874 in Outer Ring Width 0.7874 in; 20.000 mm Maximum RPM (Grease) 6100 RPM Fillet Radius 1.100 mm, 0.0433 in Maximum RPM 7100 RPM Series 60 Manufacturer UPC Number 4547359004120 Weight 1.35 lbs Harmonization Code 8482.10.5056 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6014ZZ, D=70 Radial/Deep Groove Ball Bearing - Round Bore, 70 mm ID, 110 mm OD, 20 mm Width, Double Shielded, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 70 mm Outside Diameter 110 mm Overall Width 20 mm Closure Type Double Shielded Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 9440 lbf Static Load Capacity 6950 lbf Precision Rating ISO Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 20.000 mm, 0.7874 in Outer Ring Width 0.7874 in; 20.000 mm Maximum RPM (Grease) 6100 RPM Fillet Radius 1.100 mm, 0.0433 in Maximum RPM 7100 RPM Series 60 Manufacturer UPC Number 4547359004120 Weight 1.35 lbs Harmonization Code 8482.10.5056 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6013ZZC3, D=65 Radial/Deep Groove Ball Bearing - Round Bore, 65 mm ID, 100 mm OD, 18 mm Width, Double Shielded, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 65 mm Outside Diameter 100 mm Overall Width 18 mm Closure Type Double Shielded Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 7640 lbf Static Load Capacity 5650 lbf Precision Rating ISO Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 18.000 mm, 0.7087 in Outer Ring Width 0.7087 in; 18.000 mm Maximum RPM (Grease) 6500 RPM Fillet Radius 1.100 mm, 0.0433 in Manufacturer UPC Number 4547359004083 Weight 0.97 lbs Harmonization Code 8482.10.5052 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6013ZZ, D=65 Radial/Deep Groove Ball Bearing - Round Bore, 65 mm ID, 100 mm OD, 18 mm Width, Double Shielded, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 65 mm Outside Diameter 100 mm Overall Width 18 mm Closure Type Double Shielded Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 7640 lbf Static Load Capacity 5650 lbf Precision Rating ISO Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 18.000 mm, 0.7087 in Outer Ring Width 0.7087 in; 18.000 mm Maximum RPM (Grease) 6500 RPM Fillet Radius 1.100 mm, 0.0433 in Manufacturer UPC Number 4547359004083 Weight 0.97 lbs Harmonization Code 8482.10.5052 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6011ZZ, D=55 Radial/Deep Groove Ball Bearing - Round Bore, 55 mm ID, 90 mm OD, 18 mm Width, Double Shielded, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 55 mm Outside Diameter 90 mm Overall Width 18 mm Closure Type Double Shielded Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 7080 lbf Static Load Capacity 4750 lbf Precision Rating ISO Class 0 Seal Type None Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 18.000 mm, 0.7087 in Outer Ring Width 0.7087 in; 18.000 mm Maximum RPM (Grease) 7700 RPM Fillet Radius 1.100 mm, 0.0433 in Radial Dynamic Load Capacity 28300 N Radial Static Load Capacity 21200 N Manufacturer UPC Number 4547359004007 Weight 0.853 lbs Harmonization Code 8482.10.5052 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6009ZZ, D=45 Radial/Deep Groove Ball Bearing - Round Bore, 45 mm ID, 75 mm OD, 16 mm Width, Double Shielded, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 45 mm Outside Diameter 75 mm Overall Width 16 mm Closure Type Double Shielded Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 5210 lbf Static Load Capacity 2590 lbf Precision Rating ISO Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 16.000 mm, 0.6299 in Outer Ring Width 0.6299 in; 16.000 mm Maximum RPM (Grease) 9200 RPM Fillet Radius 1.000 mm, 0.0394 in Manufacturer UPC Number 4547359003925 Weight 0.53 lbs Harmonization Code 8482.10.5052 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6008ZZC3, D=40 Radial/Deep Groove Ball Bearing - Round Bore, 40 mm ID, 68 mm OD, 15 mm Width, Double Shielded, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 40 mm Outside Diameter 68 mm Overall Width 15 mm Closure Type Double Shielded Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 4180 lbf Static Load Capacity 2590 lbf Precision Rating ISO Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 15.000 mm, 0.5906 in Outer Ring Width 0.5906 in; 15.000 mm Maximum RPM (Grease) 10000 RPM Fillet Radius 1.000 mm, 0.0394 in Maximum RPM 6100 RPM Series 60 Manufacturer UPC Number 4547359003888 Weight 0.41 lbs Harmonization Code 8482.10.5052 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN Deep Groove Ball Bearings  6008ZZ, D=40 Radial/Deep Groove Ball Bearing - Round Bore, 40 mm ID, 68 mm OD, 15 mm Width, Double Shielded, CN Internal Clearance SPECIFICATIONS Bore Type Round Bore Diameter 40 mm Outside Diameter 68 mm Overall Width 15 mm Closure Type Double Shielded Row Type & Fill Slot Single Row Non-Fill Slot Snap Ring Included Without Snap Ring Internal Clearance CN Operating Temperature Range -40 to 250 ºF Cage Type Pressed Dynamic Load Capacity 4180 lbf Static Load Capacity 2590 lbf Precision Rating ISO Class 0 Seal Type None Finish/Coating Uncoated Bearing Material High Carbon Chrome Steel Cage Material Steel Inner Ring Width 15.000 mm, 0.5906 in Outer Ring Width 0.5906 in; 15.000 mm Maximum RPM (Grease) 10000 RPM Fillet Radius 1.000 mm, 0.0394 in Maximum RPM 6100 RPM Series 60 Manufacturer UPC Number 4547359003888 Weight 0.41 lbs Harmonization Code 8482.10.5052 1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.    Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN 6316LLUC3 Deep Groove Ball Bearings , D=80   SPECIFICATIONS Type of Product : Deep Groove Ball Bearing Model No : 6316LLUC3 Width : 39 mm Inner Diameter : 80 mm       1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less