BEARING / FA

NSK Deep Groove Ball Bearings 6332M ,Single-Row  D=160   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6332M 160 340 68 4 278 287 1700 2000 13.9 26.2 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6330M ,Single-Row  D=150   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6330M 150 320 65 4 274 284 1800 2200 13.9 22.7 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6328M ,Single-Row  D=140   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6328M 140 300 62 4 253 246 2000 2400 13.6 18.5 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6326M ,Single-Row  D=130   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6326M 130 280 58 4 229 214 2200 2600 13.6 15.2 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6324 ,Single-Row  D=120 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6324 120 260 55 3 207 185 2200 2800 13.5 12.5 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6322 ,Single-Row  D=110 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6322 110 240 50 3 205 179 2400 3000 13.2 9.51 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6321 ,Single-Row  D=105 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6321 105 225 49 3 184 154 2600 3200 13.2 8.09 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6320 ,Single-Row  D=100 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6320 100 215 47 3 173 141 2800 3400 13.2 7.04 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6319 ,Single-Row  D=95 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6319 95 200 45 3 153 119 3000 3600 13.3 5.76 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6318 ,Single-Row  D=90 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6318 90 190 43 3 143 107 3600 4300 13.3 4.98 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6317 ,Single-Row  D=85 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6317 85 180 41 3 133 97 3800 4500 13.3 4.28 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6315ZZ ,Single-Row  D=75   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6315ZZ 75 160 37 2.1 113 77 4300 　 13.2 3.08 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6314ZZ ,Single-Row  D=70   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6314ZZ 70 150 35 2.1 104 68 4500 　 13.2 2.57 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6313ZZ ,Single-Row  D=65   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6313ZZ 65 140 33 2.1 92.5 60 4800 　 13.2 2.11 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6312ZZ ,Single-Row  D=60   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6312ZZ 60 130 31 2.1 82 52 5300 　 13.1 1.72 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6311ZZ ,Single-Row  D=55   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6311ZZ 55 120 29 2 71.5 44.5 5600 　 13.1 1.37 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6310ZZ ,Single-Row  D=50   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6310ZZ 50 110 27 2 62 38.5 6000 　 13.2 1.06 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6309ZZ ,Single-Row  D=45   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6309ZZ 45 100 25 1.5 53 32 6700 　 13.1 0.829 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6308ZZ ,Single-Row  D=40   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6308ZZ 40 90 23 1.5 40.5 24 7500 　 13.2 0.636 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6307ZZ ,Single-Row  D=35   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6307ZZ 35 80 21 1.5 33.5 19.2 8500 　 13.2 0.464 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6306ZZ ,Single-Row  D=30   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6306ZZ 30 72 19 1.1 26.7 15 9500 　 13.3 0.345 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6305ZZ ,Single-Row  D=25   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6305ZZ 25 62 17 1.1 20.6 11.2 11000 　 13.2 0.235 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6304ZZ ,Single-Row  D=20   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6304ZZ 20 52 15 1.1 15.9 7.9 14000 　 12.4 0.145 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6316DDU ,Single-Row  D=80 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6316DDU 80 170 39 2.1 123 86.5 2800 　 13.3 3.67 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6315DDU ,Single-Row  D=75 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6315DDU 75 160 37 2.1 113 77 2800 　 13.2 3.08 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6314DDU ,Single-Row  D=70 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6314DDU 70 150 35 2.1 104 68 3200 　 13.2 2.57 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6313DDU ,Single-Row  D=65 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6313DDU 65 140 33 2.1 92.5 60 3400 　 13.2 2.11 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6312DDU ,Single-Row  D=60 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6312DDU 60 130 31 2.1 82 52 3600 　 13.1 1.72 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6311DDU ,Single-Row  D=55 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6311DDU 55 120 29 2 71.5 44.5 4000 　 13.1 1.37 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6310DDU ,Single-Row  D=50 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6310DDU 50 110 27 2 62 38.5 4300 　 13.2 1.06 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6309DDU ,Single-Row  D=45 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6309DDU 45 100 25 1.5 53 32 4800 　 13.1 0.829 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6308DDU ,Single-Row  D=40 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6308DDU 40 90 23 1.5 40.5 24 5300 　 13.2 0.636 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6307DDU ,Single-Row  D=35 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6307DDU 35 80 21 1.5 33.5 19.2 6000 　 13.2 0.464 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6306DDU ,Single-Row  D=30 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6306DDU 30 72 19 1.1 26.7 15 6700 　 13.3 0.345 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6305DDU ,Single-Row  D=25 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6305DDU 25 62 17 1.1 20.6 11.2 8000 　 13.2 0.235 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6304DDU ,Single-Row  D=20 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6304DDU 20 52 15 1.1 15.9 7.9 10000 　 12.4 0.145 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6316VV ,Single-Row  D=80 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6316VV 80 170 39 2.1 123 86.5 4000 0 13.3 3.67 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6315VV ,Single-Row  D=75 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6315VV 75 160 37 2.1 113 77 4300 0 13.2 3.08 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6314VV ,Single-Row  D=70 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6314VV 70 150 35 2.1 104 68 4500 0 13.2 2.57 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6313VV ,Single-Row  D=65 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6313VV 65 140 33 2.1 92.5 60 4800 0 13.2 2.11 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6312VV ,Single-Row  D=60 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6312VV 60 130 31 2.1 82 52 5300 0 13.1 1.72 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6311VV ,Single-Row  D=55 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6311VV 55 120 29 2 71.5 44.5 5600 0 13.1 1.37 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6310VV ,Single-Row  D=50 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6310VV 50 110 27 2 62 38.5 6000 0 13.2 1.06 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6309VV ,Single-Row  D=45 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6309VV 45 100 25 1.5 53 32 6700 0 13.1 0.829 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6308VV ,Single-Row  D=40 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6308VV 40 90 23 1.5 40.5 24 7500 0 13.2 0.636 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6307VV ,Single-Row  D=35 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6307VV 35 80 21 1.5 33.5 19.2 8500 0 13.2 0.464 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6306VV ,Single-Row  D=30 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6306VV 30 72 19 1.1 26.7 15 9500 0 13.3 0.345 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6305VV ,Single-Row  D=25 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6305VV 25 62 17 1.1 20.6 11.2 11000 0 13.2 0.235 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less