NSK

NSK Deep Groove Ball Bearings 6904 ,Single-Row  D=20 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6904 20 37 9 0.3 6.4 3.7 19000 22000 14.7 0.037 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6903 ,Single-Row  D=17 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6903 17 30 7 0.3 4.6 2.55 24000 28000 14.7 0.017 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6902 ,Single-Row  D=15 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6902 15 28 7 0.3 4.35 2.26 26000 30000 14.3 0.015 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6900ZZ ,Single-Row  D=10   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6900ZZ 10 22 6 0.3 2.7 1.27 32000 　 14 0.009   DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6844ZZS ,Single-Row  D=220   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6844ZZS 220 270 24 1.5 76.5 107 1900 　 17.4 2.9   DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6834ZZS ,Single-Row  D=170   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6834ZZS 170 215 22 1.1 60 75 2600 　 17.1 1.59   DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6832ZZS ,Single-Row  D=160   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6832ZZS 160 200 20 1.1 48.5 61 2600 　 17.2 1.23   DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6830ZZ ,Single-Row  D=150   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6830ZZ 150 190 20 1.1 47.5 58.5 3200 　 17.1 1.15   DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6828ZZ ,Single-Row  D=140   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6828ZZ 140 175 18 1.1 38.5 48 3400 　 17.3 0.832   DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6901DD ,Single-Row  D=12 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6901DD 12 24 6 0.3 2.89 1.46 20000 　 14.5 0.01   DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6900DD ,Single-Row  D=10 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6900DD 10 22 6 0.3 2.7 1.27 22000 　 14 0.009 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6834DDU ,Single-Row  D=170 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6834DDU 170 215 22 1.1 60 75 1600 　 17.1 1.59   DESIGN, TYPES, AND FEATURES    SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6832DDU ,Single-Row  D=160 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6832DDU 160 200 20 1.1 48.5 61 1700 　 17.2 1.23   DESIGN, TYPES, AND FEATURES    SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6830DDU ,Single-Row  D=150 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6830DDU 150 190 20 1.1 47.5 58.5 1800 　 17.1 1.15   DESIGN, TYPES, AND FEATURES    SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6828DDU ,Single-Row  D=140 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6828DDU 140 175 18 1.1 38.5 48 1900 　 17.3 0.832   DESIGN, TYPES, AND FEATURES    SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6900VV ,Single-Row  D=10 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6900VV 10 22 6 0.3 2.7 1.27 32000 　 14 0.009 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6838VV ,Single-Row  D=190 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6838VV 190 240 24 1.5 73 93.5 2200 　 17.1 2.18   DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6836VV ,Single-Row  D=180 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6836VV 180 225 22 1.1 60.5 78.5 2400 　 17.2 1.72 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6834VV ,Single-Row  D=170 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6834VV 170 215 22 1.1 60 75 2600 　 17.1 1.59   DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6832VV ,Single-Row  D=160 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6832VV 160 200 20 1.1 48.5 61 2600 　 17.2 1.23 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6830VV ,Single-Row  D=150 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6830VV 150 190 20 1.1 47.5 58.5 3200 　 17.1 1.15   DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6828VV ,Single-Row  D=140 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6828VV 140 175 18 1.1 38.5 48 3400 　 17.3 0.832 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 69/750 ,Single-Row  D=750 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 69/750 750 1000 112 6 785 1840 400 500 16.7 245 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 69/710 ,Single-Row  D=710 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 69/710 710 950 106 6 715 1640 450 530 16.8 208 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 69/670 ,Single-Row  D=670 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 69/670 670 900 103 6 675 1460 480 560 16.7 181 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 69/630 ,Single-Row  D=630 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 69/630 630 850 100 6 625 1350 530 630 16.7 163 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 69/600 ,Single-Row  D=600 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 69/600 600 800 90 5 550 1160 560 670 16.9 120 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 69/560 ,Single-Row  D=560 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 69/560 560 750 85 5 525 1040 600 750 16.7 105 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 69/530 ,Single-Row  D=530 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 69/530 530 710 82 5 455 870 670 800 16.8 89.8 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 69/500 ,Single-Row  D=500 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 69/500 500 670 78 5 460 865 710 850 16.7 82 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6901 ,Single-Row  D=12 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6901 12 24 6 0.3 2.89 1.46 30000 36000 14.5 0.01 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6900 ,Single-Row  D=10 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6900 10 22 6 0.3 2.7 1.27 32000 38000 14 0.009 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6896 ,Single-Row  D=480 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6896 480 600 56 3 315 575 800 950 17.2 35.4 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6892 ,Single-Row  D=460 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6892 460 580 56 3 310 550 800 1000 17.1 34.3 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6888 ,Single-Row  D=440 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6888 440 540 46 2.1 248 425 900 1100 17.4 22.3 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6884 ,Single-Row  D=420 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6884 420 520 46 2.1 245 410 900 1100 17.3 21.4 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6880 ,Single-Row  D=400 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6880 400 500 46 2.1 241 390 950 1200 17.2 20.5 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6876 ,Single-Row  D=380 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6876 380 480 46 2.1 238 375 1000 1200 17.1 19.5 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6872 ,Single-Row  D=360 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6872 360 440 38 2.1 192 290 1100 1300 17.3 11.8 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6868 ,Single-Row  D=340 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6868 340 420 38 2.1 175 265 1200 1400 17.3 11.5 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6864 ,Single-Row  D=320 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6864 320 400 38 2.1 168 244 1300 1500 17.2 10.8 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6860 ,Single-Row  D=300 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6860 300 380 38 2.1 166 233 1300 1600 17.1 10.3 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6856 ,Single-Row  D=280 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6856 280 350 33 2 133 191 1500 1700 17.3 7.2 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6852 ,Single-Row  D=260 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6852 260 320 28 2 101 148 1600 1900 17.4 4.84 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6848 ,Single-Row  D=240 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6848 240 300 28 2 98.5 137 1700 2000 17.3 4.48 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6844 ,Single-Row  D=220 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6844 220 270 24 1.5 76.5 107 1900 2400 17.4 2.9 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6840 ,Single-Row  D=200 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6840 200 250 24 1.5 74 98 2200 2600 17.2 2.67 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6838 ,Single-Row  D=190 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6838 190 240 24 1.5 73 93.5 2200 2600 17.1 2.18 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less