NTN Deep Groove Ball Bearings

NTN 6018LLU Deep Groove Ball Bearings , D=90   SPECIFICATIONS Type of Product : Deep Groove Ball Bearing Model No : 6018LLU Width : 24 mm Inner Diameter : 90 mm       1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN 6016LLUC3 Deep Groove Ball Bearings , D=80   SPECIFICATIONS Type of Product : Deep Groove Ball Bearing Model No : 6016LLUC3 Width : 22 mm Inner Diameter : 80 mm       1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN 6016LLU  Deep Groove Ball Bearings , D=80   SPECIFICATIONS Type of Product : Deep Groove Ball Bearing Model No : 6016LLU Width : 22 mm Inner Diameter : 80 mm       1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN 6015LLU Deep Groove Ball Bearings , D=75   SPECIFICATIONS Type of Product : Deep Groove Ball Bearing Model No : 6015LLU Width : 20 mm Inner Diameter : 75 mm       1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN 6014LLUC3 Deep Groove Ball Bearings , D=70   SPECIFICATIONS Type of Product : Deep Groove Ball Bearing Model No : 6014LLUC3 Width : 20 mm Inner Diameter : 70 mm       1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN 6013LLUC3 Deep Groove Ball Bearings , D=65   SPECIFICATIONS Type of Product : Deep Groove Ball Bearing Model No : 6013LLUC3 Width : 18 mm Inner Diameter : 65 mm       1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN 6013LLU Deep Groove Ball Bearings , D=65   SPECIFICATIONS Type of Product : Deep Groove Ball Bearing Model No : 6013LLU Width : 18 mm Inner Diameter : 65 mm       1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN 6012LLUC3 Deep Groove Ball Bearings , D=60   SPECIFICATIONS Type of Product : Deep Groove Ball Bearing Model No : 6012LLUC3 Width : 18 mm Inner Diameter : 60 mm       1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN 6012LLU Deep Groove Ball Bearings , D=60   SPECIFICATIONS Type of Product : Deep Groove Ball Bearing Model No : 6012LLU Width : 18 mm Inner Diameter : 60 mm       1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN 6011LLUC3 Deep Groove Ball Bearings , D=55   SPECIFICATIONS Type of Product : Deep Groove Ball Bearing Model No : 6011LLUC3 Width : 18 mm Inner Diameter : 55 mm       1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN 6011LLU Deep Groove Ball Bearings , D=55   SPECIFICATIONS Type of Product : Deep Groove Ball Bearing Model No : 6011LLU Width : 18 mm Inner Diameter : 55 mm       1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN 6009LLUC3 Deep Groove Ball Bearings , D=45   SPECIFICATIONS Type of Product : Deep Groove Ball Bearing Model No : 6009LLUC3 Width : 16 mm Inner Diameter : 45 mm       1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN 6008LLU Deep Groove Ball Bearings , D=40   SPECIFICATIONS Type of Product : Deep Groove Ball Bearing Model No : 6008LLU Width : 15 mm Inner Diameter : 40 mm       1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN 6007LLUC3 Deep Groove Ball Bearings , D=35   SPECIFICATIONS Type of Product : Deep Groove Ball Bearing Model No : 6007LLUC3 Width : 14 mm Inner Diameter : 35 mm       1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN 6007LLU Deep Groove Ball Bearings , D=35   SPECIFICATIONS Type of Product : Deep Groove Ball Bearing Model No : 6007LLU Width : 14 mm Inner Diameter : 35 mm       1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN 6006LLUC3 Deep Groove Ball Bearings , D=30   SPECIFICATIONS Type of Product : Deep Groove Ball Bearing Model No : 6006LLUC3 Width : 13 mm Inner Diameter : 30 mm       1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN 6006LLU Deep Groove Ball Bearings , D=30   SPECIFICATIONS Type of Product : Deep Groove Ball Bearing Model No : 6006LLU Width : 13 mm Inner Diameter : 30 mm       1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN 6005LLUC3 Deep Groove Ball Bearings , D=25   SPECIFICATIONS Type of Product : Deep Groove Ball Bearing Model No : 6005LLUC3 Width : 12 mm Inner Diameter : 25 mm       1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN 6005LLU Deep Groove Ball Bearings , D=25   SPECIFICATIONS Type of Product : Deep Groove Ball Bearing Model No : 6005LLU Width : 12 mm Inner Diameter : 25 mm       1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN 6004LLU Deep Groove Ball Bearings , D=20   SPECIFICATIONS Type of Product : Deep Groove Ball Bearing Model No : 6004LLU Width : 12 mm Inner Diameter : 20 mm       1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN 6003LLUC3 Deep Groove Ball Bearings , D=17   SPECIFICATIONS Type of Product : Deep Groove Ball Bearing Model No : 6003LLUC3 Width : 10 mm Inner Diameter : 17 mm       1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN 6002LLUC3 Deep Groove Ball Bearings , D=15   SPECIFICATIONS Type of Product : Deep Groove Ball Bearing Model No : 6002LLUC3 Width : 9 mm Inner Diameter : 15 mm       1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN 6002LLU Deep Groove Ball Bearings , D=15   SPECIFICATIONS Type of Product : Deep Groove Ball Bearing Model No : 6002LLU Width : 9 mm Inner Diameter : 15 mm       1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN 6001LLUC3 Deep Groove Ball Bearings , D=12   SPECIFICATIONS Type of Product : Deep Groove Ball Bearing Model No : 6001LLUC3 Width : 8 mm Inner Diameter : 12 mm       1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less

NTN 6001LLU  Deep Groove Ball Bearings , D=12   SPECIFICATIONS Type of Product : Deep Groove Ball Bearing Model No : 6001LLU Width : 8 mm Inner Diameter : 12 mm       1. Design features and characteristics Deep groove ball bearings are very widely used. A deep groove is formed on the inner and outer ring of the bearing enabling the bearing to sustain radial and axial loads in either direction as well as the complex loads which result from the combination of these forces. Deep groove ball bearings are suitable for high speed applications. When two or more deep groove ball bearings are used in combination and mounted adjacent to each other a duplex set (D2) should be used. Duplex bearings (D2) utilize controlled tolerances to more evenly distribute the loading between the individual bearing rows which improves the overall performance of the assembly. In addition to unsealed and unlubricated “open” bearings, NTN provides deep groove ball bearings that are pre-lubricated with grease and enclosed by seals or shields. See section “11. Lubrication” for a list of some of the greases which can be used. Table 1 shows the construction and special characteristics of various sealed deep groove ball bearings.  Types and codes N Shielded type Shielded type Non-contact type ZZ Non-contact type LLB Contact type LLU Low torque type LLH Construction Metal shield plate is affixed to the outside ring; the inner ring incorporates a V-groove and labyrinth clearance. The outer ring incorporates synthetic rubber molded to a steel plate; seal edge is aligned with V-groove along inner ring surface with labyrinth clearance The outer ring incorporates synthetic rubber molded to a steel plate; seal edge contacts V-groove along inner ring surface Basic construction is the same as LLU type, but a specially designed lip on the edge of the seal prevents foreign matter penetration; low torque construction. Torque Small Small Higher Medium Dust proofing Good Better than ZZ-type Excellent Much better than LLB-type Water proofing Poor Poor Very good Good High speed capacity Same as open type Same as open type Limited by contact seals Much better than LLU-type Allowable temp. range Depends on lubricant −25 to 120°C −25 to 110°C −25 to 120°C

Read more less