NSK Deep Groove Ball Bearings

NSK Deep Groove Ball Bearings 6038ZZS ,Single-Row  D=190 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6038ZZS 190 290 46 2.1 188 201 2000 　 15.8 9.39   DESIGN, TYPES, AND FEATURES    SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6902VV ,Single-Row  D=15 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6902VV 15 28 7 0.3 4.35 2.26 26000 　 14.3 0.015 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6303 ,Single-Row  D=17 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6303 17 47 14 1 13.6 6.65 15000 18000 12.4 0.113 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6206VV ,Single-Row  D=30 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6206VV 30 62 16 1 19.5 11.3 11000 0 13.8 0.199 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6202VV ,Single-Row  D=15 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6202VV 15 35 11 0.6 7.65 3.75 20000 0 13.2 0.045 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6206 ,Single-Row  D=30 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6206 30 62 16 1 19.5 11.3 11000 13000 13.8 0.199 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6205 ,Single-Row  D=25 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6205 25 52 15 1 14 7.85 13000 15000 13.9 0.129 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6204 ,Single-Row  D=20 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6204 20 47 14 1 12.8 6.6 15000 18000 13.1 0.107 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6012VV ,Single-Row  D=60 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6012VV 60 95 18 1.1 29.5 23.2 7100 0 15.6 0.412 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6010VV ,Single-Row  D=50 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6010VV 50 80 16 1 21.8 16.6 8500 0 15.6 0.261 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6005VV ,Single-Row  D=25 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6005VV 25 47 12 0.6 10.1 5.85 15000 0 14.5 0.079 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6004VV ,Single-Row  D=20 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6004VV 20 42 12 0.6 9.4 5 18000 0 13.8 0.068 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6002VV ,Single-Row  D=15 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6002VV 15 32 9 0.3 5.6 2.83 24000 0 13.9 0.031 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6948ZZS ,Single-Row  D=240   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6948ZZS 240 320 38 2.1 154 190 1700 　 16.8 8.49 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6944ZZS ,Single-Row  D=220   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6944ZZS 220 300 38 2.1 146 169 1800 　 16.6 7.88 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6940ZZS ,Single-Row  D=200   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6940ZZS 200 280 38 2.1 143 158 2000 　 16.4 7.28 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6936ZZS ,Single-Row  D=180   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6936ZZS 180 250 33 2 119 128 2200 　 16.4 4.16 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6934ZZS ,Single-Row  D=170   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6934ZZS 170 230 28 2 86 97 2400 　 16.7 2.85 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6932ZZS ,Single-Row  D=160   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6932ZZS 160 220 28 2 87 96 2600 　 16.6 2.71 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6930ZZS ,Single-Row  D=150   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6930ZZS 150 210 28 2 85 90.5 2600 　 16.5 2.59 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6928ZZS ,Single-Row  D=140   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6928ZZS 140 190 24 1.5 66.5 72 3200 　 16.6 1.67 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6926ZZ ,Single-Row  D=130   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6926ZZ 130 180 24 1.5 65 67.5 3400 　 16.5 1.57 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6924ZZ ,Single-Row  D=120   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6924ZZ 120 165 22 1.1 53 54 3800 　 16.5 1.21 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6932DDU ,Single-Row  D=160 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6932DDU 160 220 28 2 87 96 1600 　 16.6 2.71   DESIGN, TYPES, AND FEATURES    SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6930DDU ,Single-Row  D=150 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6930DDU 150 210 28 2 85 90.5 1700 　 16.5 2.59   DESIGN, TYPES, AND FEATURES    SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6928VV ,Single-Row  D=140 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6928VV 140 190 24 1.5 66.5 72 3200 　 16.6 1.67 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6928N , Single-Row With a Snap Ring Groove D=140.0 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6928N 140 190 24 1.5 66.5 72 3200 3800 16.6 1.67 DESIGN, TYPES, AND FEATURES    SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6926N , Single-Row With a Snap Ring Groove D=130.0 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6926N 130 180 24 1.5 65 67.5 3400 4000 16.5 1.57 DESIGN, TYPES, AND FEATURES    SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6996 ,Single-Row  D=480 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6996 480 650 78 5 450 815 750 900 16.6 73.5 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6992 ,Single-Row  D=460 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6992 460 620 74 4 405 720 800 950 16.7 62.6 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6988 ,Single-Row  D=440 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6988 440 600 74 4 395 680 800 1000 16.6 60.2 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6984 ,Single-Row  D=420 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6984 420 560 65 4 340 570 900 1100 16.8 43.6 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6980 ,Single-Row  D=400 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6980 400 540 65 4 335 540 900 1100 16.7 42 . DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6976 ,Single-Row  D=380 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6976 380 520 65 4 325 510 950 1200 16.6 40 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6972 ,Single-Row  D=360 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6972 360 480 56 3 280 425 1100 1300 16.7 27.9 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6968 ,Single-Row  D=340 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6968 340 460 56 3 273 400 1100 1300 16.6 26.6 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6964 ,Single-Row  D=320 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6964 320 440 56 3 266 375 1200 1400 16.5 25.3 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6960 ,Single-Row  D=300 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6960 300 420 56 3 269 370 1300 1500 16.4 23.9 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6956 ,Single-Row  D=280 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6956 280 380 46 2.1 209 272 1400 1700 16.6 15.1 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6952 ,Single-Row  D=260 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6952 260 360 46 2.1 204 255 1500 1800 16.5 14 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6948M ,Single-Row  D=240   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6948M 240 320 38 2.1 154 190 1700 2000 16.8 8.49 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6944M ,Single-Row  D=220   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6944M 220 300 38 2.1 146 169 1800 2200 16.6 7.88 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6940M ,Single-Row  D=200   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6940M 200 280 38 2.1 143 158 2000 2400 16.4 7.28 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6938M ,Single-Row  D=190   Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6938M 190 260 33 2 113 127 2200 2600 16.6 5.18 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6936 ,Single-Row  D=180 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6936 180 250 33 2 119 128 2200 2600 16.4 4.16 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6934 ,Single-Row  D=170 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6934 170 230 28 2 86 97 2400 2800 16.7 2.85 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6932 ,Single-Row  D=160 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6932 160 220 28 2 87 96 2600 3000 16.6 2.71 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6930 ,Single-Row  D=150 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6930 150 210 28 2 85 90.5 2600 3200 16.5 2.59 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less