NSK Deep Groove Ball Bearings

NSK Deep Groove Ball Bearings 6006DDU ,Single-Row  D=30 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6006DDU 30 55 13 1 13.2 8.3 8000 　 14.7 0.116 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6005DDU ,Single-Row  D=25 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6005DDU 25 47 12 0.6 10.1 5.85 9500 　 14.5 0.079 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6004DDU ,Single-Row  D=20 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6004DDU 20 42 12 0.6 9.4 5 11000 　 13.8 0.068 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6002DDU ,Single-Row  D=15 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6002DDU 15 32 9 0.3 5.6 2.83 15000 　 13.9 0.031 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6001DDU ,Single-Row  D=12 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6001DDU 12 28 8 0.3 5.1 2.37 18000 　 13 0.022 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6000DDU ,Single-Row  D=10 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6000DDU 10 26 8 0.3 4.55 1.97 22000 　 12.4 0.018 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6009VV ,Single-Row  D=45 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6009VV 45 75 16 1 20.9 15.2 9000 0 15.3 0.241 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6008VV ,Single-Row  D=40 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6008VV 40 68 15 1 16.8 11.5 10000 0 15.3 0.19 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6007VV ,Single-Row  D=35 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6007VV 35 62 14 1 16 10.3 11000 0 14.8 0.151 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6006VV ,Single-Row  D=30 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6006VV 30 55 13 1 13.2 8.3 13000 0 14.7 0.116 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6003VV ,Single-Row  D=17 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6003VV 17 35 10 0.3 6 3.25 22000 0 14.4 0.041 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6001VV ,Single-Row  D=12 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6001VV 12 28 8 0.3 5.1 2.37 28000 0 13 0.022 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6000VV ,Single-Row  D=10 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6000VV 10 26 8 0.3 4.55 1.97 30000 0 12.4 0.018 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6011 ,Single-Row  D=55 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6011 55 90 18 1.1 28.3 21.2 7500 9000 15.3 0.381 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6010 ,Single-Row  D=50 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6010 50 80 16 1 21.8 16.6 8500 10000 15.6 0.261 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6009 ,Single-Row  D=45 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6009 45 75 16 1 20.9 15.2 9000 11000 15.3 0.241 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6008 ,Single-Row  D=40 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6008 40 68 15 1 16.8 11.5 10000 12000 15.3 0.19 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6007 , Single-Row, D=35 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6007 35 62 14 1 16 10.3 11000 13000 14.8 0.151 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6006 ,Single-Row  D=30 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6006 30 55 13 1 13.2 8.3 13000 15000 14.7 0.116 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6005 ,Single-Row  D=25 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6005 25 47 12 0.6 10.1 5.85 15000 18000 14.5 0.079 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6004 ,Single-Row  D=20 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6004 20 42 12 0.6 9.4 5 18000 20000 13.8 0.068 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6003 ,Single-Row  D=17  Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6003 17 35 10 0.3 6 3.25 22000 26000 14.4 0.041 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6002 ,Single-Row  D=15 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6002 15 32 9 0.3 5.6 2.83 24000 28000 13.9 0.031 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6001 ,Single-Row  D=12 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6001 12 28 8 0.3 5.1 2.37 28000 32000 13 0.022 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less

NSK Deep Groove Ball Bearings 6000 ,Single-Row  D=10 Bearing Numbers Boundary Dimensions (mm) Basic Load Ratings (kN) Limiting Speeds (min-1) Factor f0 Mass (kg) approx. d D B r min. Cr C0r Grease Oil 6000 10 26 8 0.3 4.55 1.97 30000 36000 12.4 0.018 DESIGN, TYPES, AND FEATURES  SINGLE-ROW DEEP GROOVE BALL BEARINGS  Single-row deep groove ball bearings are classified into the types shown below. The proper amount of good quality grease is packed in shielded and sealed ball bearings. A comparison of the features of each type is shown in Table 1. Table 1 Features of Sealed Ball Bearings  Type  Shielded (ZZ Type) Rubber Non-Contact Seal (VV Type)  Rubber Contact Seal (DDU Type)  Torque Low Low Higher than ZZ and VV types  due to contact seal   Speed capability  Good Good Limited by contact seals  Grease-sealing effectiveness  Good Better than ZZ type  Slightly better than VV type  Dust resistance Good Better than ZZ type (usable in moderately dusty environments) Best (usable even in very dusty environments)  Water resistance Not suitable Not suitable Good (usable even if fluid is splashed on bearing)   Operating temperature –10 to +110 °C –10 to +110 °C –10 to +110 °C   Note (1) The above temperature range applies to standard bearings. By using  cold- or heat-resistant grease or changing the type of rubber, the  operating temperature range can be extended.      □Formulation of Bearing Designations Single-row deep groove ball bearings ①Bearing type 6 : Single-row deep groove ball bearings ②Dimension Series 2 : 02 Series, 3 : 03 Series, 9 : 19 Series, 0 : 10 Series ③Bore number Less than 03, Bearing bore 00 : 10mm, 01 : 12mm, 02 : 15mm, 03 : 17mm Over 04, Bearing bore bore number X 5 (mm) ④Seals/shields   ZZ : Shield on both sides, DDU: Rubber contact seal on both sides, VV: Rubber non-contact seal on both sides, Z: Shield on one side, DU: Rubber contact seal on one side V:Rubber non-contact seal on one side ⑤Internal clearance Omitted : CN clearance＊1, C3 : Clearance greater than CN, C4 : Clearance greater than C3, CM : For electric motors＊1 ⑥NSKHPS designation & : NSKHPSTM Bearings ⑦Grease designation＊2 NS7 : NS HI-LUBE ＊1 CM clearance may be used instead of CN clearance (the reverse is not possible). ＊2 The grease designation is required when seals/shields are used on both sides.  NSKHPS™ Deep Groove Ball Bearings Note (1) The above temperature range applies to standard bearings. By using cold- or heat-resistant grease or changing the type of rubber, the operating temperature range can be extended. Compared with conventional bearings: ● Improved reliabilityBearing life is 15% longer than conventional bearings thanks to optimization of the bearing’s internal design and improvement of processing technology. As a result, NSKHPS™ bearings contribute to reducing maintenance costs and facilitate the downscaling of related equipment.● New product lineupThe standard dimensions are identical to standard size bearings. NSK has expanded the lineup of NSKHPS™ bearings by focusing on a wide range of sizes offering a high degree of versatility for various general-purpose applications.

Read more less