Sensors & PLC
Autonics Autonics Fiber optic sensor FD-620-F2
FD-620-F2 Type : Standard type(bolt type) Sensing distance : 120mm Min. sensing target : Ø0.03mm Allowable bend radius : R30 Cable length : 2m Environment_Ambient temperature : -40 to 70℃ Type Standard type(bolt type) Sensing distance 120mm Min. sensing target Ø0.03mm Allowable bend radius R30 Cable length 2m Free cut Free cut Environment_Ambient temperature -40 to 70℃ Sensing type Diffuse reflective type ※The sensing distance is a standard for red LED of BF4 Series and 10% of red LED is applied when it is green LED. It is applied to 40% of sensing distance for BF3RX.※Min. sensing target is a value measured opaque material in accurate output status and the sensing distance is different with the rated sensing distance.※Free cut type's sensing distance can be shortened about max. 20% than the normal according to condition of the cable. [(FC-3) should be used for cutting fiber cable.]※Glass type is for BF5, BF4 Series.
$19.13
Autonics Autonics Fiber optic sensor, Diffuse reflective type FDC-320-05
FDC-320-05 Type : Cylinder type Sensing distance : 40mm Min. sensing target : Ø0.03mm Allowable bend radius : R15 Cable length : 2m Adapter : Adapter Environment_Ambient temperature : -40 to 70℃ Type Cylinder type Sensing distance 40mm Min. sensing target Ø0.03mm Allowable bend radius R15 Cable length 2m Free cut Free cut Adapter Adapter Environment_Ambient temperature -40 to 70℃ Sensing type Diffuse reflective type
$16.54
Autonics Autonics Fiber optic sensor, Diffuse reflective type FDC-320-06B
FDC-320-06B Type : Cylinder type Sensing distance : 35mm Min. sensing target : Ø0.0125mm Allowable bend radius : R5 Cable length : 2m Adapter : Adapter Environment_Ambient temperature : -40 to 60℃ Type Cylinder type Sensing distance 35mm Min. sensing target Ø0.0125mm Allowable bend radius R5 Cable length 2m Free cut Free cut Adapter Adapter Environment_Ambient temperature -40 to 60℃ Sensing type Diffuse reflective type ※The sensing distance is a standard for red LED of BF4 Series and 10% of red LED is applied when it is green LED. It is applied to 40% of sensing distance for BF3RX.※Min. sensing target is a value measured opaque material in accurate output status and the sensing distance is different with the rated sensing distance.※Flexible optical fiber (Multi core): A large number of ultra-fine cores are all surrounded by cladding. Easy to install it in the many places as the change of the intensity of radiation by bending is small.Break-resistant optical fiber: The fiber units contain a large number of independent fine fibers, by ensuring a high degree of flexibility. It can be used for moving parts (robot hand) and it is not easily broken.※Free cut type's sensing distance can be shortened about max. 20% than the normal according to condition of the cable. [(FC-3) should be used for cutting fiber cable.]※Glass type is for BF5, BF4 Series.
$25.27
Autonics Autonics Fiber optic sensor, Diffuse reflective type FDF-210-05R
FDF-210-05R Type : Flat type/Flat view Sensing distance : 30mm Min. sensing target : Ø0.0125mm Allowable bend radius : R1 Cable length : 1m Adapter : Adapter Environment_Ambient temperature : -40 to 60℃ Type Flat type/Flat view Sensing distance 30mm Min. sensing target Ø0.0125mm Allowable bend radius R1 Cable length 1m Free cut Free cut Adapter Adapter Environment_Ambient temperature -40 to 60℃ Sensing type Diffuse reflective type
$57.47
Autonics Autonics Fiber optic sensor, Diffuse reflective type FDFN-210-05R
FDFN-210-05R Type : Flat type/Side view Sensing distance : 30mm Min. sensing target : Ø0.0125mm Allowable bend radius : R1 Cable length : 1m Adapter : Adapter Environment_Ambient temperature : -40 to 60℃ Type Flat type/Side view Sensing distance 30mm Min. sensing target Ø0.0125mm Allowable bend radius R1 Cable length 1m Free cut Free cut Adapter Adapter Environment_Ambient temperature -40 to 60℃ Sensing type Diffuse reflective type
$57.47
Autonics Autonics Fiber optic sensor, Plastic injection molding type FDP-320-10
FDP-320-10 Type : Plastic injection molding type Sensing distance : 120mm Min. sensing target : Ø0.03mm Allowable bend radius : R25 Cable length : 2m Environment_Ambient temperature : -40 to 70℃ Type Plastic injection molding type Sensing distance 120mm Min. sensing target Ø0.03mm Allowable bend radius R25 Cable length 2m Free cut Free cut Environment_Ambient temperature -40 to 70℃ Sensing type Diffuse reflective type ※The sensing distance is a standard for red LED of BF4 Series and 10% of red LED is applied when it is green LED. It is applied to 40% of sensing distance for BF3RX.※Min. sensing target is a value measured opaque material in accurate output status and the sensing distance is different with the rated sensing distance.※Free cut type's sensing distance can be shortened about max. 20% than the normal according to condition of the cable. [(FC-3) should be used for cutting fiber cable.]※Glass type is for BF5, BF4 Series.
$10.40
Autonics Autonics Fiber optic sensor, Plastic injection molding type FDPF-210-05R
FDPF-210-05R Type : Plastic injection molding type Sensing distance : 70mm Min. sensing target : Ø0.08mm Allowable bend radius : R1 Cable length : 1m Adapter : Adapter Environment_Ambient temperature : -30 to 70℃ Type Plastic injection molding type Sensing distance 70mm Min. sensing target Ø0.08mm Allowable bend radius R1 Cable length 1m Free cut Free cut Adapter Adapter Environment_Ambient temperature -30 to 70℃ Sensing type Diffuse reflective type
$105.54
Autonics Autonics Fiber optic sensor, Diffuse reflective type FDR-610-10R
FDR-610-10R Type : Right-angle Sensing distance : 120mm Min. sensing target : Ø0.04mm Allowable bend radius : R1 Cable length : 1m Environment_Ambient temperature : -40 to 60℃ Type Right-angle Sensing distance 120mm Min. sensing target Ø0.04mm Allowable bend radius R1 Cable length 1m Free cut Free cut Environment_Ambient temperature -40 to 60℃ Sensing type Diffuse reflective type ※The sensing distance is a standard for BF5 Series.※Min. sensing target is a value measured opaque material in accurate output status and the sensing distance is different with the rated sensing distance.※Free cut type's sensing distance can be shortened about max. 20% than the normal according to condition of the cable. [(FC-3) should be used for cutting fiber cable.]※Glass type is for BF5, BF4 Series.
$53.11
Autonics Autonics Fiber optic sensor, Diffuse reflective type FDRT-420-02B
FDRT-420-02B Type : Right-angle Sensing distance : 230mm Min. sensing target : Ø0.08mm Allowable bend radius : R5 Cable length : 2m Environment_Ambient temperature : -30 to 70℃ Type Right-angle Sensing distance 230mm Min. sensing target Ø0.08mm Allowable bend radius R5 Cable length 2m Free cut Free cut Environment_Ambient temperature -30 to 70℃ Sensing type Diffuse reflective type
$95.05
Autonics Autonics Fiber optic sensor FDS-420-05
FDS-420-05 Type : SUS type(SUS length 90mm) Sensing distance : 40mm Min. sensing target : Ø0.03mm Allowable bend radius : 15R(SUS part 10R) Cable length : 2m Adapter : Adapter Environment_Ambient temperature : -40 to 70℃ Type SUS type(SUS length 90mm) Sensing distance 40mm Min. sensing target Ø0.03mm Allowable bend radius 15R(SUS part 10R) Cable length 2m Free cut Free cut Adapter Adapter Environment_Ambient temperature -40 to 70℃ Sensing type Diffuse reflective type ※The sensing distance is a standard for red LED of BF4 Series and 10% of red LED is applied when it is green LED. It is applied to 40% of sensing distance for BF3RX.※Min. sensing target is a value measured opaque material in accurate output status and the sensing distance is different with the rated sensing distance.※Free cut type's sensing distance can be shortened about max. 20% than the normal according to condition of the cable. [(FC-3) should be used for cutting fiber cable.]※Glass type is for BF5, BF4 Series.
$27.84
Autonics Autonics Fiber optic sensor, Diffuse reflective type FDS2-420-05
FDS2-420-05 Type : SUS type(SUS length 45mm) Sensing distance : 40mm Min. sensing target : Ø0.03mm Allowable bend radius : 15R(SUS part 10R) Cable length : 2m Adapter : Adapter Environment_Ambient temperature : -40 to 70℃ Type SUS type(SUS length 45mm) Sensing distance 40mm Min. sensing target Ø0.03mm Allowable bend radius 15R(SUS part 10R) Cable length 2m Free cut Free cut Adapter Adapter Environment_Ambient temperature -40 to 70℃ Sensing type Diffuse reflective type ※The sensing distance is a standard for red LED of BF4 Series and 10% of red LED is applied when it is green LED. It is applied to 40% of sensing distance for BF3RX.※Min. sensing target is a value measured opaque material in accurate output status and the sensing distance is different with the rated sensing distance.※Free cut type's sensing distance can be shortened about max. 20% than the normal according to condition of the cable. [(FC-3) should be used for cutting fiber cable.]※Glass type is for BF5, BF4 Series.
$28.74
Autonics Autonics Fiber optic sensor, Diffuse reflective type FDS2-620-10
FDS2-620-10 Type : SUS type(SUS length 45mm) Sensing distance : 120mm Min. sensing target : Ø0.03mm Allowable bend radius : R25(SUS part R10) Cable length : 2m Environment_Ambient temperature : -40 to 70℃ Type SUS type(SUS length 45mm) Sensing distance 120mm Min. sensing target Ø0.03mm Allowable bend radius R25(SUS part R10) Cable length 2m Free cut Free cut Environment_Ambient temperature -40 to 70℃ Sensing type Diffuse reflective type ※The sensing distance is a standard for red LED of BF4 Series and 10% of red LED is applied when it is green LED. It is applied to 40% of sensing distance for BF3RX.※Min. sensing target is a value measured opaque material in accurate output status and the sensing distance is different with the rated sensing distance.※Free cut type's sensing distance can be shortened about max. 20% than the normal according to condition of the cable. [(FC-3) should be used for cutting fiber cable.]※Glass type is for BF5, BF4 Series.
$21.81
Autonics Autonics Fiber optic sensor, Area type FDW10-320-02B
FDW10-320-02B Type : Area type Sensing distance : 230mm Min. sensing target : Ø0.08mm Allowable bend radius : R5 Cable length : 2m Environment_Ambient temperature : -30 to 70℃ Type Area type Sensing distance 230mm Min. sensing target Ø0.08mm Allowable bend radius R5 Cable length 2m Free cut Free cut Environment_Ambient temperature -30 to 70℃ Sensing type Diffuse reflective type
$137.76
Autonics Autonics Fiber optic sensor, Area type FDW10T-320-02B
FDW10T-320-02B Type : Area type Sensing distance : 230mm Min. sensing target : Ø0.08mm Allowable bend radius : R5 Cable length : 2m Environment_Ambient temperature : -30 to 70℃ Type Area type Sensing distance 230mm Min. sensing target Ø0.08mm Allowable bend radius R5 Cable length 2m Free cut Free cut Environment_Ambient temperature -30 to 70℃ Sensing type Diffuse reflective type
$148.27
Autonics Autonics Fiber optic sensor, Convergent reflective type FLF-310-10V
FLF-310-10V Type : Flat type/Flat view Sensing distance : 60mm(FU-VA01)/70mm(FU-VA02) Min. sensing target : Ø3.9mm(FU-VA01)/Ø3.4mm(FU-VA02) Allowable bend radius : R25 Cable length : 1m Environment_Ambient temperature : -30 to 105℃ Type Flat type/Flat view Sensing distance 60mm(FU-VA01)/70mm(FU-VA02) Min. sensing target Ø3.9mm(FU-VA01)/Ø3.4mm(FU-VA02) Allowable bend radius R25 Cable length 1m Free cut Free cut Environment_Ambient temperature -30 to 105℃ Sensing type Convergent reflective type
$379.33
Autonics Autonics Fiber optic sensor, Convergent reflective type FLF-320-05
FLF-320-05 Type : Flat type/Flat view Sensing distance : 8mm Min. sensing target : Ø0.1mm Allowable bend radius : R15 Cable length : 2m Adapter : Adapter Environment_Ambient temperature : -30 to 70℃ Type Flat type/Flat view Sensing distance 8mm Min. sensing target Ø0.1mm Allowable bend radius R15 Cable length 2m Free cut Free cut Adapter Adapter Environment_Ambient temperature -30 to 70℃ Sensing type Convergent reflective type
$95.94
Autonics Autonics Fiber optic sensor, Convergent reflective type FLF-320-05R
FLF-320-05R Type : Flat type/Flat view Sensing distance : 7mm Min. sensing target : Ø0.08mm Allowable bend radius : R1 Cable length : 2m Adapter : Adapter Environment_Ambient temperature : -30 to 70℃ Type Flat type/Flat view Sensing distance 7mm Min. sensing target Ø0.08mm Allowable bend radius R1 Cable length 2m Free cut Free cut Adapter Adapter Environment_Ambient temperature -30 to 70℃ Sensing type Convergent reflective type
$119.50
Autonics Autonics Fiber optic sensor, Convergent reflective type FLF-320-10
FLF-320-10 Type : Flat type/Flat view Sensing distance : 8mm Min. sensing target : Ø0.0125mm Allowable bend radius : R25 Cable length : 2m Environment_Ambient temperature : -40 to 60℃ Type Flat type/Flat view Sensing distance 8mm Min. sensing target Ø0.0125mm Allowable bend radius R25 Cable length 2m Environment_Ambient temperature -40 to 60℃ Sensing type Convergent reflective type ※The sensing distance is a standard for BF5 Series.※Free cut type's sensing distance can be shortened about max. 20% than the normal according to condition of the cable. [(FC-3) should be used for cutting fiber cable.]
$86.32
Autonics Autonics Fiber optic sensor, Convergent reflective type FLF-320-10A
FLF-320-10A Type : Flat type/Flat view Sensing distance : 100mm Min. sensing target : Ø0.08mm Allowable bend radius : R20 Cable length : 2m Adapter : Adapter Environment_Ambient temperature : -30 to 70℃ Type Flat type/Flat view Sensing distance 100mm Min. sensing target Ø0.08mm Allowable bend radius R20 Cable length 2m Free cut Free cut Adapter Adapter Environment_Ambient temperature -30 to 70℃ Sensing type Convergent reflective type
$95.08
Autonics Autonics Fiber optic sensor, Convergent reflective type FLF-320-10H
FLF-320-10H Type : Flat type/Flat view Sensing distance : 130mm Min. sensing target : Ø0.08mm Allowable bend radius : R25 Cable length : 2m Environment_Ambient temperature : -40 to 105℃ Type Flat type/Flat view Sensing distance 130mm Min. sensing target Ø0.08mm Allowable bend radius R25 Cable length 2m Free cut Free cut Environment_Ambient temperature -40 to 105℃ Sensing type Convergent reflective type
$158.74
Autonics Autonics photoelectric micro sensor, Through-beam type BS3-F1M-P
Sensing type Through-beam type Sensing distance 5mm Sensing target Opaque Min. sensing target ≥ 0.8 mm × 1.8 mm Hysteresis(distance) ≤0.05mm Response time Light ON: Max. 20㎲, Dark ON: Max. 100㎲ Response frequency 2kHz Light source Infrared LED Peak emission wavelength 940nm Operation mode Light ON/Dark ON(set by control wire) Indicator Operation indicator (red LED) Weight Approx. 50g Power voltage 5-24VDC ±10%(ripple P-P : max. 10%) Current consumption Max. 15mA Control output PNP open collector Load voltage ≤ 24VDC Load current Max. 50mA Residual voltage NPN: ≤1.2VDC, PNP: ≤ 1.2VDC Protection circuit Reverse polarity protection circuit, output overcurrent (short-circuit) protection circuit Insulation resistance ≥20 MΩ (250 VDC megger) Noise immunity The square wave noise (pulse width: 1㎲) by the noise simulator ±240VDC Dielectric strength 1,000VAC 50/60Hz for 1 minute Vibration 1.5mm amplitude (max. acceleration 196m/s²) at frequency of 10 to 2,000Hz in each X, Y, Z direction for 2 hours Shock 15,000 m/s² (approx. 1,500G) in each X, Y, Z direction for 3 times Environment_Ambient illumination Fluorescent lamp: Max. 1,000lx(received illumination) Environment_Ambient temperature -20 to 55℃, storage : -25 to 85℃ Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Protection structure IP50 (IEC standard) Connection Cable type Connection type Ø2.5mm, 4-wire, 1m Core AWG28 (0.08mm), 19-core, insulator out diameter: Ø0.65mm Material Case: PBT, Sensing part: PC
$12.97
Autonics Autonics photoelectric micro sensor ,Through-beam type BS3-F1R
Sensing type Through-beam type Sensing distance 5mm Sensing target Opaque Min. sensing target ≥ 0.8 mm × 1.8 mm Hysteresis(distance) ≤0.05mm Response time Light ON: Max. 20㎲, Dark ON: Max. 100㎲ Response frequency 2kHz Light source Infrared LED Peak emission wavelength 940nm Operation mode Light ON/Dark ON(set by control wire) Indicator Operation indicator (red LED) Weight Approx. 50g Power voltage 5-24VDC ±10%(ripple P-P : max. 10%) Current consumption Max. 15mA Control output NPN open collector Load voltage ≤ 24VDC Load current Max. 50mA Residual voltage NPN: ≤1.2VDC, PNP: ≤ 1.2VDC Protection circuit Reverse polarity protection circuit, output overcurrent (short-circuit) protection circuit Insulation resistance ≥20 MΩ (250 VDC megger) Noise immunity The square wave noise (pulse width: 1㎲) by the noise simulator ±240VDC Dielectric strength 1,000VAC 50/60Hz for 1 minute Vibration 1.5mm amplitude (max. acceleration 196m/s²) at frequency of 10 to 2,000Hz in each X, Y, Z direction for 2 hours Shock 15,000 m/s² (approx. 1,500G) in each X, Y, Z direction for 3 times Environment_Ambient illumination Fluorescent lamp: Max. 1,000lx(received illumination) Environment_Ambient temperature -20 to 55℃, storage : -25 to 85℃ Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Protection structure IP50 (IEC standard) Connection Cable type Connection type Ø2.5mm, 4-wire, 1m Core AWG28 (0.08mm), 19-core, insulator out diameter: Ø0.65mm Material Case: PBT, Sensing part: PC
$12.94
Autonics Autonics photoelectric micro sensor, Through-beam type BS3-K1M-P
Sensing type Through-beam type Sensing distance 5mm Sensing target Opaque Min. sensing target ≥ 0.8 mm × 1.8 mm Hysteresis(distance) ≤0.05mm Response time Light ON: Max. 20㎲, Dark ON: Max. 100㎲ Response frequency 2kHz Light source Infrared LED Peak emission wavelength 940nm Operation mode Light ON/Dark ON(set by control wire) Indicator Operation indicator (red LED) Weight Approx. 50g Power voltage 5-24VDC ±10%(ripple P-P : max. 10%) Current consumption Max. 15mA Control output PNP open collector Load voltage ≤ 24VDC Load current Max. 50mA Residual voltage NPN: ≤1.2VDC, PNP: ≤ 1.2VDC Protection circuit Reverse polarity protection circuit, output overcurrent (short-circuit) protection circuit Insulation resistance ≥20 MΩ (250 VDC megger) Noise immunity The square wave noise (pulse width: 1㎲) by the noise simulator ±240VDC Dielectric strength 1,000VAC 50/60Hz for 1 minute Vibration 1.5mm amplitude (max. acceleration 196m/s²) at frequency of 10 to 2,000Hz in each X, Y, Z direction for 2 hours Shock 15,000 m/s² (approx. 1,500G) in each X, Y, Z direction for 3 times Environment_Ambient illumination Fluorescent lamp: Max. 1,000lx(received illumination) Environment_Ambient temperature -20 to 55℃, storage : -25 to 85℃ Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Protection structure IP50 (IEC standard) Connection Cable type Connection type Ø2.5mm, 4-wire, 1m Core AWG28 (0.08mm), 19-core, insulator out diameter: Ø0.65mm Material Case: PBT, Sensing part: PC
$12.97
Autonics Autonics photoelectric micro sensor, Through-beam type BS3-K1R
Sensing type Through-beam type Sensing distance 5mm Sensing target Opaque Min. sensing target ≥ 0.8 mm × 1.8 mm Hysteresis(distance) ≤0.05mm Response time Light ON: Max. 20㎲, Dark ON: Max. 100㎲ Response frequency 2kHz Light source Infrared LED Peak emission wavelength 940nm Operation mode Light ON/Dark ON(set by control wire) Indicator Operation indicator (red LED) Weight Approx. 50g Power voltage 5-24VDC ±10%(ripple P-P : max. 10%) Current consumption Max. 15mA Control output NPN open collector Load voltage ≤ 24VDC Load current Max. 50mA Residual voltage NPN: ≤1.2VDC, PNP: ≤ 1.2VDC Protection circuit Reverse polarity protection circuit, output overcurrent (short-circuit) protection circuit Insulation resistance ≥20 MΩ (250 VDC megger) Noise immunity The square wave noise (pulse width: 1㎲) by the noise simulator ±240VDC Dielectric strength 1,000VAC 50/60Hz for 1 minute Vibration 1.5mm amplitude (max. acceleration 196m/s²) at frequency of 10 to 2,000Hz in each X, Y, Z direction for 2 hours Shock 15,000 m/s² (approx. 1,500G) in each X, Y, Z direction for 3 times Environment_Ambient illumination Fluorescent lamp: Max. 1,000lx(received illumination) Environment_Ambient temperature -20 to 55℃, storage : -25 to 85℃ Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Protection structure IP50 (IEC standard) Connection Cable type Connection type Ø2.5mm, 4-wire, 1m Core AWG28 (0.08mm), 19-core, insulator out diameter: Ø0.65mm Material Case: PBT, Sensing part: PC
$12.94
Autonics Autonics photoelectric micro sensor, Through-beam type BS3-K1R-P
Sensing type Through-beam type Sensing distance 5mm Sensing target Opaque Min. sensing target ≥ 0.8 mm × 1.8 mm Hysteresis(distance) ≤0.05mm Response time Light ON: Max. 20㎲, Dark ON: Max. 100㎲ Response frequency 2kHz Light source Infrared LED Peak emission wavelength 940nm Operation mode Light ON/Dark ON(set by control wire) Indicator Operation indicator (red LED) Weight Approx. 50g Power voltage 5-24VDC ±10%(ripple P-P : max. 10%) Current consumption Max. 15mA Control output PNP open collector Load voltage ≤ 24VDC Load current Max. 50mA Residual voltage NPN: ≤1.2VDC, PNP: ≤ 1.2VDC Protection circuit Reverse polarity protection circuit, output overcurrent (short-circuit) protection circuit Insulation resistance ≥20 MΩ (250 VDC megger) Noise immunity The square wave noise (pulse width: 1㎲) by the noise simulator ±240VDC Dielectric strength 1,000VAC 50/60Hz for 1 minute Vibration 1.5mm amplitude (max. acceleration 196m/s²) at frequency of 10 to 2,000Hz in each X, Y, Z direction for 2 hours Shock 15,000 m/s² (approx. 1,500G) in each X, Y, Z direction for 3 times Environment_Ambient illumination Fluorescent lamp: Max. 1,000lx(received illumination) Environment_Ambient temperature -20 to 55℃, storage : -25 to 85℃ Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Protection structure IP50 (IEC standard) Connection Cable type Connection type Ø2.5mm, 4-wire, 1m Core AWG28 (0.08mm), 19-core, insulator out diameter: Ø0.65mm Material Case: PBT, Sensing part: PC
$12.94
Autonics Autonics photoelectric micro sensor, Through-beam type BS3-L1M-P
Sensing type Through-beam type Sensing distance 5mm Sensing target Opaque Min. sensing target ≥ 0.8 mm × 1.8 mm Hysteresis(distance) ≤0.05mm Response time Light ON: Max. 20㎲, Dark ON: Max. 100㎲ Response frequency 2kHz Light source Infrared LED Peak emission wavelength 940nm Operation mode Light ON/Dark ON(set by control wire) Indicator Operation indicator (red LED) Weight Approx. 50g Power voltage 5-24VDC ±10%(ripple P-P : max. 10%) Current consumption Max. 15mA Control output PNP open collector Load voltage ≤ 24VDC Load current Max. 50mA Residual voltage NPN: ≤1.2VDC, PNP: ≤ 1.2VDC Protection circuit Reverse polarity protection circuit, output overcurrent (short-circuit) protection circuit Insulation resistance ≥20 MΩ (250 VDC megger) Noise immunity The square wave noise (pulse width: 1㎲) by the noise simulator ±240VDC Dielectric strength 1,000VAC 50/60Hz for 1 minute Vibration 1.5mm amplitude (max. acceleration 196m/s²) at frequency of 10 to 2,000Hz in each X, Y, Z direction for 2 hours Shock 15,000 m/s² (approx. 1,500G) in each X, Y, Z direction for 3 times Environment_Ambient illumination Fluorescent lamp: Max. 1,000lx(received illumination) Environment_Ambient temperature -20 to 55℃, storage : -25 to 85℃ Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Protection structure IP50 (IEC standard) Connection Cable type Connection type Ø2.5mm, 4-wire, 1m Core AWG28 (0.08mm), 19-core, insulator out diameter: Ø0.65mm Material Case: PBT, Sensing part: PC
$12.97
Autonics Autonics photoelectric micro sensor Through-beam type BS3-L1R-P
Sensing type Through-beam type Sensing distance 5mm Sensing target Opaque Min. sensing target ≥ 0.8 mm × 1.8 mm Hysteresis(distance) ≤0.05mm Response time Light ON: Max. 20㎲, Dark ON: Max. 100㎲ Response frequency 2kHz Light source Infrared LED Peak emission wavelength 940nm Operation mode Light ON/Dark ON(set by control wire) Indicator Operation indicator (red LED) Weight Approx. 50g Power voltage 5-24VDC ±10%(ripple P-P : max. 10%) Current consumption Max. 15mA Control output PNP open collector Load voltage ≤ 24VDC Load current Max. 50mA Residual voltage NPN: ≤1.2VDC, PNP: ≤ 1.2VDC Protection circuit Reverse polarity protection circuit, output overcurrent (short-circuit) protection circuit Insulation resistance ≥20 MΩ (250 VDC megger) Noise immunity The square wave noise (pulse width: 1㎲) by the noise simulator ±240VDC Dielectric strength 1,000VAC 50/60Hz for 1 minute Vibration 1.5mm amplitude (max. acceleration 196m/s²) at frequency of 10 to 2,000Hz in each X, Y, Z direction for 2 hours Shock 15,000 m/s² (approx. 1,500G) in each X, Y, Z direction for 3 times Environment_Ambient illumination Fluorescent lamp: Max. 1,000lx(received illumination) Environment_Ambient temperature -20 to 55℃, storage : -25 to 85℃ Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Protection structure IP50 (IEC standard) Connection Cable type Connection type Ø2.5mm, 4-wire, 1m Core AWG28 (0.08mm), 19-core, insulator out diameter: Ø0.65mm Material Case: PBT, Sensing part: PC
$12.94
Autonics Autonics photoelectric micro sensor Through-beam type BS3-R1R
Sensing type Through-beam type Sensing distance 5mm Sensing target Opaque Min. sensing target ≥ 0.8 mm × 1.8 mm Hysteresis(distance) ≤0.05mm Response time Light ON: Max. 20㎲, Dark ON: Max. 100㎲ Response frequency 2kHz Light source Infrared LED Peak emission wavelength 940nm Operation mode Light ON/Dark ON(set by control wire) Indicator Operation indicator (red LED) Weight Approx. 50g Power voltage 5-24VDC ±10%(ripple P-P : max. 10%) Current consumption Max. 15mA Control output NPN open collector Load voltage ≤ 24VDC Load current Max. 50mA Residual voltage NPN: ≤1.2VDC, PNP: ≤ 1.2VDC Protection circuit Reverse polarity protection circuit, output overcurrent (short-circuit) protection circuit Insulation resistance ≥20 MΩ (250 VDC megger) Noise immunity The square wave noise (pulse width: 1㎲) by the noise simulator ±240VDC Dielectric strength 1,000VAC 50/60Hz for 1 minute Vibration 1.5mm amplitude (max. acceleration 196m/s²) at frequency of 10 to 2,000Hz in each X, Y, Z direction for 2 hours Shock 15,000 m/s² (approx. 1,500G) in each X, Y, Z direction for 3 times Environment_Ambient illumination Fluorescent lamp: Max. 1,000lx(received illumination) Environment_Ambient temperature -20 to 55℃, storage : -25 to 85℃ Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Protection structure IP50 (IEC standard) Connection Cable type Connection type Ø2.5mm, 4-wire, 1m Core AWG28 (0.08mm), 19-core, insulator out diameter: Ø0.65mm Material Case: PBT, Sensing part: PC
$12.94
Autonics Autonics photoelectric micro sensor Through-beam type BS3-R1R-P
Sensing type Through-beam type Sensing distance 5mm Sensing target Opaque Min. sensing target ≥ 0.8 mm × 1.8 mm Hysteresis(distance) ≤0.05mm Response time Light ON: Max. 20㎲, Dark ON: Max. 100㎲ Response frequency 2kHz Light source Infrared LED Peak emission wavelength 940nm Operation mode Light ON/Dark ON(set by control wire) Indicator Operation indicator (red LED) Weight Approx. 50g Power voltage 5-24VDC ±10%(ripple P-P : max. 10%) Current consumption Max. 15mA Control output PNP open collector Load voltage ≤ 24VDC Load current Max. 50mA Residual voltage NPN: ≤1.2VDC, PNP: ≤ 1.2VDC Protection circuit Reverse polarity protection circuit, output overcurrent (short-circuit) protection circuit Insulation resistance ≥20 MΩ (250 VDC megger) Noise immunity The square wave noise (pulse width: 1㎲) by the noise simulator ±240VDC Dielectric strength 1,000VAC 50/60Hz for 1 minute Vibration 1.5mm amplitude (max. acceleration 196m/s²) at frequency of 10 to 2,000Hz in each X, Y, Z direction for 2 hours Shock 15,000 m/s² (approx. 1,500G) in each X, Y, Z direction for 3 times Environment_Ambient illumination Fluorescent lamp: Max. 1,000lx(received illumination) Environment_Ambient temperature -20 to 55℃, storage : -25 to 85℃ Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Protection structure IP50 (IEC standard) Connection Cable type Connection type Ø2.5mm, 4-wire, 1m Core AWG28 (0.08mm), 19-core, insulator out diameter: Ø0.65mm Material Case: PBT, Sensing part: PC
$12.94
Autonics Autonics photoelectric micro sensor Through-beam type BS3-U1R
Sensing type Through-beam type Sensing distance 5mm Sensing target Opaque Min. sensing target ≥ 0.8 mm × 1.8 mm Hysteresis(distance) ≤0.05mm Response time Light ON: Max. 20㎲, Dark ON: Max. 100㎲ Response frequency 2kHz Light source Infrared LED Peak emission wavelength 940nm Operation mode Light ON/Dark ON(set by control wire) Indicator Operation indicator (red LED) Weight Approx. 50g Power voltage 5-24VDC ±10%(ripple P-P : max. 10%) Current consumption Max. 15mA Control output NPN open collector Load voltage ≤ 24VDC Load current Max. 50mA Residual voltage NPN: ≤1.2VDC, PNP: ≤ 1.2VDC Protection circuit Reverse polarity protection circuit, output overcurrent (short-circuit) protection circuit Insulation resistance ≥20 MΩ (250 VDC megger) Noise immunity The square wave noise (pulse width: 1㎲) by the noise simulator ±240VDC Dielectric strength 1,000VAC 50/60Hz for 1 minute Vibration 1.5mm amplitude (max. acceleration 196m/s²) at frequency of 10 to 2,000Hz in each X, Y, Z direction for 2 hours Shock 15,000 m/s² (approx. 1,500G) in each X, Y, Z direction for 3 times Environment_Ambient illumination Fluorescent lamp: Max. 1,000lx(received illumination) Environment_Ambient temperature -20 to 55℃, storage : -25 to 85℃ Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Protection structure IP50 (IEC standard) Connection Cable type Connection type Ø2.5mm, 4-wire, 1m Core AWG28 (0.08mm), 19-core, insulator out diameter: Ø0.65mm Material Case: PBT, Sensing part: PC
$12.94
Autonics Autonics photoelectric micro sensor Through-beam type BS3-U1R-P
Sensing type Through-beam type Sensing distance 5mm Sensing target Opaque Min. sensing target ≥ 0.8 mm × 1.8 mm Hysteresis(distance) ≤0.05mm Response time Light ON: Max. 20㎲, Dark ON: Max. 100㎲ Response frequency 2kHz Light source Infrared LED Peak emission wavelength 940nm Operation mode Light ON/Dark ON(set by control wire) Indicator Operation indicator (red LED) Weight Approx. 50g Power voltage 5-24VDC ±10%(ripple P-P : max. 10%) Current consumption Max. 15mA Control output PNP open collector Load voltage ≤ 24VDC Load current Max. 50mA Residual voltage NPN: ≤1.2VDC, PNP: ≤ 1.2VDC Protection circuit Reverse polarity protection circuit, output overcurrent (short-circuit) protection circuit Insulation resistance ≥20 MΩ (250 VDC megger) Noise immunity The square wave noise (pulse width: 1㎲) by the noise simulator ±240VDC Dielectric strength 1,000VAC 50/60Hz for 1 minute Vibration 1.5mm amplitude (max. acceleration 196m/s²) at frequency of 10 to 2,000Hz in each X, Y, Z direction for 2 hours Shock 15,000 m/s² (approx. 1,500G) in each X, Y, Z direction for 3 times Environment_Ambient illumination Fluorescent lamp: Max. 1,000lx(received illumination) Environment_Ambient temperature -20 to 55℃, storage : -25 to 85℃ Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Protection structure IP50 (IEC standard) Connection Cable type Connection type Ø2.5mm, 4-wire, 1m Core AWG28 (0.08mm), 19-core, insulator out diameter: Ø0.65mm Material Case: PBT, Sensing part: PC
$12.94
Autonics Autonics photoelectric micro sensor Through-beam type BS4-F2M
Sensing type Through-beam type Sensing distance 5mm Sensing target Opaque Min. sensing target ≥ 0.8 mm × 1.8 mm Hysteresis(distance) ≤0.05mm Response time Light ON: Max. 20㎲,Dark ON: Max. 80㎲ Response frequency 2kHz Light source Infrared LED Peak emission wavelength 940nm Operation mode Light ON/Dark ON(Built-in) Indicator Operation indicator (red LED) Weight ≈ 2.4 g Power voltage 5-24VDC ±10%(ripple P-P : max. 10%) Current consumption Max. 15mA Control output NPN open collector Load voltage ≤ 24VDC Load current Max. 50mA Residual voltage NPN: ≤1.2VDC, PNP: ≤ 1.2VDC Protection circuit Reverse polarity protection circuit, output overcurrent (short-circuit) protection circuit Insulation resistance ≥20 MΩ (250 VDC megger) Noise immunity The square wave noise (pulse width: 1㎲) by the noise simulator ±240VDC Dielectric strength 1,000VAC~ 50/60Hz for 1 minute Vibration 1.5mm amplitude (max. acceleration 196m/s²) at frequency of 10 to 2,000Hz in each X, Y, Z direction for 2 hours Shock 15,000 m/s² (approx. 1,500G) in each X, Y, Z direction for 3 times Environment_Ambient illumination Fluorescent lamp: Max. 1,000lx(received illumination) Environment_Ambient temperature -20 to 55℃, storage : -25 to 85℃ Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Protection structure IP50 (IEC standard) Connection Connector type Material Case: PBT, Sensing part: PC
$10.10
Autonics Autonics photoelectric micro sensor Through-beam type BS4-F2M-P
Sensing type Through-beam type Sensing distance 5mm Sensing target Opaque Min. sensing target ≥ 0.8 mm × 1.8 mm Hysteresis(distance) ≤0.05mm Response time Light ON: Max. 20㎲,Dark ON: Max. 80㎲ Response frequency 2kHz Light source Infrared LED Peak emission wavelength 940nm Operation mode Light ON/Dark ON(Built-in) Indicator Operation indicator (red LED) Weight ≈ 2.4 g Power voltage 5-24VDC ±10%(ripple P-P : max. 10%) Current consumption Max. 15mA Control output PNP open collector Load voltage ≤ 24VDC Load current Max. 50mA Residual voltage NPN: ≤1.2VDC, PNP: ≤ 1.2VDC Protection circuit Reverse polarity protection circuit, output overcurrent (short-circuit) protection circuit Insulation resistance ≥20 MΩ (250 VDC megger) Noise immunity The square wave noise (pulse width: 1㎲) by the noise simulator ±240VDC Dielectric strength 1,000VAC~ 50/60Hz for 1 minute Vibration 1.5mm amplitude (max. acceleration 196m/s²) at frequency of 10 to 2,000Hz in each X, Y, Z direction for 2 hours Shock 15,000 m/s² (approx. 1,500G) in each X, Y, Z direction for 3 times Environment_Ambient illumination Fluorescent lamp: Max. 1,000lx(received illumination) Environment_Ambient temperature -20 to 55℃, storage : -25 to 85℃ Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Protection structure IP50 (IEC standard) Connection Connector type Material Case: PBT, Sensing part: PC
$10.19
Autonics Autonics photoelectric micro sensor Through-beam type BS4-F2R
Sensing type Through-beam type Sensing distance 5mm Sensing target Opaque Min. sensing target ≥ 0.8 mm × 1.8 mm Hysteresis(distance) ≤0.05mm Response time Light ON: Max. 20㎲,Dark ON: Max. 80㎲ Response frequency 2kHz Light source Infrared LED Peak emission wavelength 940nm Operation mode Light ON/Dark ON(Built-in) Indicator Operation indicator (red LED) Weight ≈ 2.4 g Power voltage 5-24VDC ±10%(ripple P-P : max. 10%) Current consumption Max. 15mA Control output NPN open collector Load voltage ≤ 24VDC Load current Max. 50mA Residual voltage NPN: ≤1.2VDC, PNP: ≤ 1.2VDC Protection circuit Reverse polarity protection circuit, output overcurrent (short-circuit) protection circuit Insulation resistance ≥20 MΩ (250 VDC megger) Noise immunity The square wave noise (pulse width: 1㎲) by the noise simulator ±240VDC Dielectric strength 1,000VAC~ 50/60Hz for 1 minute Vibration 1.5mm amplitude (max. acceleration 196m/s²) at frequency of 10 to 2,000Hz in each X, Y, Z direction for 2 hours Shock 15,000 m/s² (approx. 1,500G) in each X, Y, Z direction for 3 times Environment_Ambient illumination Fluorescent lamp: Max. 1,000lx(received illumination) Environment_Ambient temperature -20 to 55℃, storage : -25 to 85℃ Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Protection structure IP50 (IEC standard) Connection Connector type Material Case: PBT, Sensing part: PC
$10.10
Autonics Autonics photoelectric micro sensor Through-beam type BS4-F2R-P
Sensing type Through-beam type Sensing distance 5mm Sensing target Opaque Min. sensing target ≥ 0.8 mm × 1.8 mm Hysteresis(distance) ≤0.05mm Response time Light ON: Max. 20㎲,Dark ON: Max. 80㎲ Response frequency 2kHz Light source Infrared LED Peak emission wavelength 940nm Operation mode Light ON/Dark ON(Built-in) Indicator Operation indicator (red LED) Weight ≈ 2.4 g Power voltage 5-24VDC ±10%(ripple P-P : max. 10%) Current consumption Max. 15mA Control output PNP open collector Load voltage ≤ 24VDC Load current Max. 50mA Residual voltage NPN: ≤1.2VDC, PNP: ≤ 1.2VDC Protection circuit Reverse polarity protection circuit, output overcurrent (short-circuit) protection circuit Insulation resistance ≥20 MΩ (250 VDC megger) Noise immunity The square wave noise (pulse width: 1㎲) by the noise simulator ±240VDC Dielectric strength 1,000VAC~ 50/60Hz for 1 minute Vibration 1.5mm amplitude (max. acceleration 196m/s²) at frequency of 10 to 2,000Hz in each X, Y, Z direction for 2 hours Shock 15,000 m/s² (approx. 1,500G) in each X, Y, Z direction for 3 times Environment_Ambient illumination Fluorescent lamp: Max. 1,000lx(received illumination) Environment_Ambient temperature -20 to 55℃, storage : -25 to 85℃ Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Protection structure IP50 (IEC standard) Connection Connector type Material Case: PBT, Sensing part: PC
$10.10
Autonics Autonics photoelectric micro sensor Through-beam type BS4-K2M
Sensing type Through-beam type Sensing distance 5mm Sensing target Opaque Min. sensing target ≥ 0.8 mm × 1.8 mm Hysteresis(distance) ≤0.05mm Response time Light ON: Max. 20㎲,Dark ON: Max. 80㎲ Response frequency 2kHz Light source Infrared LED Peak emission wavelength 940nm Operation mode Light ON/Dark ON(Built-in) Indicator Operation indicator (red LED) Weight ≈ 2.4 g Power voltage 5-24VDC ±10%(ripple P-P : max. 10%) Current consumption Max. 15mA Control output NPN open collector Load voltage ≤ 24VDC Load current Max. 50mA Residual voltage NPN: ≤1.2VDC, PNP: ≤ 1.2VDC Protection circuit Reverse polarity protection circuit, output overcurrent (short-circuit) protection circuit Insulation resistance ≥20 MΩ (250 VDC megger) Noise immunity The square wave noise (pulse width: 1㎲) by the noise simulator ±240VDC Dielectric strength 1,000VAC~ 50/60Hz for 1 minute Vibration 1.5mm amplitude (max. acceleration 196m/s²) at frequency of 10 to 2,000Hz in each X, Y, Z direction for 2 hours Shock 15,000 m/s² (approx. 1,500G) in each X, Y, Z direction for 3 times Environment_Ambient illumination Fluorescent lamp: Max. 1,000lx(received illumination) Environment_Ambient temperature -20 to 55℃, storage : -25 to 85℃ Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Protection structure IP50 (IEC standard) Connection Connector type Material Case: PBT, Sensing part: PC
$10.10
Autonics Autonics photoelectric micro sensor Through-beam type BS4-K2M-P
Sensing type Through-beam type Sensing distance 5mm Sensing target Opaque Min. sensing target ≥ 0.8 mm × 1.8 mm Hysteresis(distance) ≤0.05mm Response time Light ON: Max. 20㎲,Dark ON: Max. 80㎲ Response frequency 2kHz Light source Infrared LED Peak emission wavelength 940nm Operation mode Light ON/Dark ON(Built-in) Indicator Operation indicator (red LED) Weight ≈ 2.4 g Power voltage 5-24VDC ±10%(ripple P-P : max. 10%) Current consumption Max. 15mA Control output PNP open collector Load voltage ≤ 24VDC Load current Max. 50mA Residual voltage NPN: ≤1.2VDC, PNP: ≤ 1.2VDC Protection circuit Reverse polarity protection circuit, output overcurrent (short-circuit) protection circuit Insulation resistance ≥20 MΩ (250 VDC megger) Noise immunity The square wave noise (pulse width: 1㎲) by the noise simulator ±240VDC Dielectric strength 1,000VAC~ 50/60Hz for 1 minute Vibration 1.5mm amplitude (max. acceleration 196m/s²) at frequency of 10 to 2,000Hz in each X, Y, Z direction for 2 hours Shock 15,000 m/s² (approx. 1,500G) in each X, Y, Z direction for 3 times Environment_Ambient illumination Fluorescent lamp: Max. 1,000lx(received illumination) Environment_Ambient temperature -20 to 55℃, storage : -25 to 85℃ Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Protection structure IP50 (IEC standard) Connection Connector type Material Case: PBT, Sensing part: PC
$10.19
Autonics Autonics photoelectric micro sensor Through-beam type BS4-K2R
Sensing type Through-beam type Sensing distance 5mm Sensing target Opaque Min. sensing target ≥ 0.8 mm × 1.8 mm Hysteresis(distance) ≤0.05mm Response time Light ON: Max. 20㎲,Dark ON: Max. 80㎲ Response frequency 2kHz Light source Infrared LED Peak emission wavelength 940nm Operation mode Light ON/Dark ON(Built-in) Indicator Operation indicator (red LED) Weight ≈ 2.4 g Power voltage 5-24VDC ±10%(ripple P-P : max. 10%) Current consumption Max. 15mA Control output NPN open collector Load voltage ≤ 24VDC Load current Max. 50mA Residual voltage NPN: ≤1.2VDC, PNP: ≤ 1.2VDC Protection circuit Reverse polarity protection circuit, output overcurrent (short-circuit) protection circuit Insulation resistance ≥20 MΩ (250 VDC megger) Noise immunity The square wave noise (pulse width: 1㎲) by the noise simulator ±240VDC Dielectric strength 1,000VAC~ 50/60Hz for 1 minute Vibration 1.5mm amplitude (max. acceleration 196m/s²) at frequency of 10 to 2,000Hz in each X, Y, Z direction for 2 hours Shock 15,000 m/s² (approx. 1,500G) in each X, Y, Z direction for 3 times Environment_Ambient illumination Fluorescent lamp: Max. 1,000lx(received illumination) Environment_Ambient temperature -20 to 55℃, storage : -25 to 85℃ Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Protection structure IP50 (IEC standard) Connection Connector type Material Case: PBT, Sensing part: PC
$10.10
Autonics Autonics photoelectric micro sensor Through-beam type BS4-K2R-P
Sensing type Through-beam type Sensing distance 5mm Sensing target Opaque Min. sensing target ≥ 0.8 mm × 1.8 mm Hysteresis(distance) ≤0.05mm Response time Light ON: Max. 20㎲,Dark ON: Max. 80㎲ Response frequency 2kHz Light source Infrared LED Peak emission wavelength 940nm Operation mode Light ON/Dark ON(Built-in) Indicator Operation indicator (red LED) Weight ≈ 2.4 g Power voltage 5-24VDC ±10%(ripple P-P : max. 10%) Current consumption Max. 15mA Control output PNP open collector Load voltage ≤ 24VDC Load current Max. 50mA Residual voltage NPN: ≤1.2VDC, PNP: ≤ 1.2VDC Protection circuit Reverse polarity protection circuit, output overcurrent (short-circuit) protection circuit Insulation resistance ≥20 MΩ (250 VDC megger) Noise immunity The square wave noise (pulse width: 1㎲) by the noise simulator ±240VDC Dielectric strength 1,000VAC~ 50/60Hz for 1 minute Vibration 1.5mm amplitude (max. acceleration 196m/s²) at frequency of 10 to 2,000Hz in each X, Y, Z direction for 2 hours Shock 15,000 m/s² (approx. 1,500G) in each X, Y, Z direction for 3 times Environment_Ambient illumination Fluorescent lamp: Max. 1,000lx(received illumination) Environment_Ambient temperature -20 to 55℃, storage : -25 to 85℃ Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Protection structure IP50 (IEC standard) Connection Connector type Material Case: PBT, Sensing part: PC
$10.10
Autonics Autonics photoelectric micro sensor Through-beam type BS4-L2M
Sensing type Through-beam type Sensing distance 5mm Sensing target Opaque Min. sensing target ≥ 0.8 mm × 1.8 mm Hysteresis(distance) ≤0.05mm Response time Light ON: Max. 20㎲,Dark ON: Max. 80㎲ Response frequency 2kHz Light source Infrared LED Peak emission wavelength 940nm Operation mode Light ON/Dark ON(Built-in) Indicator Operation indicator (red LED) Weight ≈ 2.4 g Power voltage 5-24VDC ±10%(ripple P-P : max. 10%) Current consumption Max. 15mA Control output NPN open collector Load voltage ≤ 24VDC Load current Max. 50mA Residual voltage NPN: ≤1.2VDC, PNP: ≤ 1.2VDC Protection circuit Reverse polarity protection circuit, output overcurrent (short-circuit) protection circuit Insulation resistance ≥20 MΩ (250 VDC megger) Noise immunity The square wave noise (pulse width: 1㎲) by the noise simulator ±240VDC Dielectric strength 1,000VAC~ 50/60Hz for 1 minute Vibration 1.5mm amplitude (max. acceleration 196m/s²) at frequency of 10 to 2,000Hz in each X, Y, Z direction for 2 hours Shock 15,000 m/s² (approx. 1,500G) in each X, Y, Z direction for 3 times Environment_Ambient illumination Fluorescent lamp: Max. 1,000lx(received illumination) Environment_Ambient temperature -20 to 55℃, storage : -25 to 85℃ Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Protection structure IP50 (IEC standard) Connection Connector type Material Case: PBT, Sensing part: PC
$10.10
Autonics Autonics photoelectric micro sensor Through-beam type BS4-L2M-P
Sensing type Through-beam type Sensing distance 5mm Sensing target Opaque Min. sensing target ≥ 0.8 mm × 1.8 mm Hysteresis(distance) ≤0.05mm Response time Light ON: Max. 20㎲,Dark ON: Max. 80㎲ Response frequency 2kHz Light source Infrared LED Peak emission wavelength 940nm Operation mode Light ON/Dark ON(Built-in) Indicator Operation indicator (red LED) Weight ≈ 2.4 g Power voltage 5-24VDC ±10%(ripple P-P : max. 10%) Current consumption Max. 15mA Control output PNP open collector Load voltage ≤ 24VDC Load current Max. 50mA Residual voltage NPN: ≤1.2VDC, PNP: ≤ 1.2VDC Protection circuit Reverse polarity protection circuit, output overcurrent (short-circuit) protection circuit Insulation resistance ≥20 MΩ (250 VDC megger) Noise immunity The square wave noise (pulse width: 1㎲) by the noise simulator ±240VDC Dielectric strength 1,000VAC~ 50/60Hz for 1 minute Vibration 1.5mm amplitude (max. acceleration 196m/s²) at frequency of 10 to 2,000Hz in each X, Y, Z direction for 2 hours Shock 15,000 m/s² (approx. 1,500G) in each X, Y, Z direction for 3 times Environment_Ambient illumination Fluorescent lamp: Max. 1,000lx(received illumination) Environment_Ambient temperature -20 to 55℃, storage : -25 to 85℃ Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Protection structure IP50 (IEC standard) Connection Connector type Material Case: PBT, Sensing part: PC
$10.10
Autonics Autonics photoelectric micro sensor Through-beam type BS4-L2R
Sensing type Through-beam type Sensing distance 5mm Sensing target Opaque Min. sensing target ≥ 0.8 mm × 1.8 mm Hysteresis(distance) ≤0.05mm Response time Light ON: Max. 20㎲,Dark ON: Max. 80㎲ Response frequency 2kHz Light source Infrared LED Peak emission wavelength 940nm Operation mode Light ON/Dark ON(Built-in) Indicator Operation indicator (red LED) Weight ≈ 2.4 g Power voltage 5-24VDC ±10%(ripple P-P : max. 10%) Current consumption Max. 15mA Control output NPN open collector Load voltage ≤ 24VDC Load current Max. 50mA Residual voltage NPN: ≤1.2VDC, PNP: ≤ 1.2VDC Protection circuit Reverse polarity protection circuit, output overcurrent (short-circuit) protection circuit Insulation resistance ≥20 MΩ (250 VDC megger) Noise immunity The square wave noise (pulse width: 1㎲) by the noise simulator ±240VDC Dielectric strength 1,000VAC~ 50/60Hz for 1 minute Vibration 1.5mm amplitude (max. acceleration 196m/s²) at frequency of 10 to 2,000Hz in each X, Y, Z direction for 2 hours Shock 15,000 m/s² (approx. 1,500G) in each X, Y, Z direction for 3 times Environment_Ambient illumination Fluorescent lamp: Max. 1,000lx(received illumination) Environment_Ambient temperature -20 to 55℃, storage : -25 to 85℃ Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Protection structure IP50 (IEC standard) Connection Connector type Material Case: PBT, Sensing part: PC
$10.10
Autonics Autonics photoelectric micro sensor Through-beam type BS4-L2R-P
Sensing type Through-beam type Sensing distance 5mm Sensing target Opaque Min. sensing target ≥ 0.8 mm × 1.8 mm Hysteresis(distance) ≤0.05mm Response time Light ON: Max. 20㎲,Dark ON: Max. 80㎲ Response frequency 2kHz Light source Infrared LED Peak emission wavelength 940nm Operation mode Light ON/Dark ON(Built-in) Indicator Operation indicator (red LED) Weight ≈ 2.4 g Power voltage 5-24VDC ±10%(ripple P-P : max. 10%) Current consumption Max. 15mA Control output PNP open collector Load voltage ≤ 24VDC Load current Max. 50mA Residual voltage NPN: ≤1.2VDC, PNP: ≤ 1.2VDC Protection circuit Reverse polarity protection circuit, output overcurrent (short-circuit) protection circuit Insulation resistance ≥20 MΩ (250 VDC megger) Noise immunity The square wave noise (pulse width: 1㎲) by the noise simulator ±240VDC Dielectric strength 1,000VAC~ 50/60Hz for 1 minute Vibration 1.5mm amplitude (max. acceleration 196m/s²) at frequency of 10 to 2,000Hz in each X, Y, Z direction for 2 hours Shock 15,000 m/s² (approx. 1,500G) in each X, Y, Z direction for 3 times Environment_Ambient illumination Fluorescent lamp: Max. 1,000lx(received illumination) Environment_Ambient temperature -20 to 55℃, storage : -25 to 85℃ Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Protection structure IP50 (IEC standard) Connection Connector type Material Case: PBT, Sensing part: PC
$10.19
Autonics Autonics photoelectric micro sensor Through-beam type BS4-R2M
Sensing type Through-beam type Sensing distance 5mm Sensing target Opaque Min. sensing target ≥ 0.8 mm × 1.8 mm Hysteresis(distance) ≤0.05mm Response time Light ON: Max. 20㎲,Dark ON: Max. 80㎲ Response frequency 2kHz Light source Infrared LED Peak emission wavelength 940nm Operation mode Light ON/Dark ON(Built-in) Indicator Operation indicator (red LED) Weight ≈ 2.4 g Power voltage 5-24VDC ±10%(ripple P-P : max. 10%) Current consumption Max. 15mA Control output NPN open collector Load voltage ≤ 24VDC Load current Max. 50mA Residual voltage NPN: ≤1.2VDC, PNP: ≤ 1.2VDC Protection circuit Reverse polarity protection circuit, output overcurrent (short-circuit) protection circuit Insulation resistance ≥20 MΩ (250 VDC megger) Noise immunity The square wave noise (pulse width: 1㎲) by the noise simulator ±240VDC Dielectric strength 1,000VAC~ 50/60Hz for 1 minute Vibration 1.5mm amplitude (max. acceleration 196m/s²) at frequency of 10 to 2,000Hz in each X, Y, Z direction for 2 hours Shock 15,000 m/s² (approx. 1,500G) in each X, Y, Z direction for 3 times Environment_Ambient illumination Fluorescent lamp: Max. 1,000lx(received illumination) Environment_Ambient temperature -20 to 55℃, storage : -25 to 85℃ Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Protection structure IP50 (IEC standard) Connection Connector type Material Case: PBT, Sensing part: PC
$10.10
Autonics Autonics photoelectric micro sensor Through-beam type BS4-R2M-P
Sensing type Through-beam type Sensing distance 5mm Sensing target Opaque Min. sensing target ≥ 0.8 mm × 1.8 mm Hysteresis(distance) ≤0.05mm Response time Light ON: Max. 20㎲,Dark ON: Max. 80㎲ Response frequency 2kHz Light source Infrared LED Peak emission wavelength 940nm Operation mode Light ON/Dark ON(Built-in) Indicator Operation indicator (red LED) Weight ≈ 2.4 g Power voltage 5-24VDC ±10%(ripple P-P : max. 10%) Current consumption Max. 15mA Control output PNP open collector Load voltage ≤ 24VDC Load current Max. 50mA Residual voltage NPN: ≤1.2VDC, PNP: ≤ 1.2VDC Protection circuit Reverse polarity protection circuit, output overcurrent (short-circuit) protection circuit Insulation resistance ≥20 MΩ (250 VDC megger) Noise immunity The square wave noise (pulse width: 1㎲) by the noise simulator ±240VDC Dielectric strength 1,000VAC~ 50/60Hz for 1 minute Vibration 1.5mm amplitude (max. acceleration 196m/s²) at frequency of 10 to 2,000Hz in each X, Y, Z direction for 2 hours Shock 15,000 m/s² (approx. 1,500G) in each X, Y, Z direction for 3 times Environment_Ambient illumination Fluorescent lamp: Max. 1,000lx(received illumination) Environment_Ambient temperature -20 to 55℃, storage : -25 to 85℃ Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Protection structure IP50 (IEC standard) Connection Connector type Material Case: PBT, Sensing part: PC
$10.19
Autonics Autonics photoelectric micro sensor Through-beam type BS4-R2R
Sensing type Through-beam type Sensing distance 5mm Sensing target Opaque Min. sensing target ≥ 0.8 mm × 1.8 mm Hysteresis(distance) ≤0.05mm Response time Light ON: Max. 20㎲,Dark ON: Max. 80㎲ Response frequency 2kHz Light source Infrared LED Peak emission wavelength 940nm Operation mode Light ON/Dark ON(Built-in) Indicator Operation indicator (red LED) Weight ≈ 2.4 g Power voltage 5-24VDC ±10%(ripple P-P : max. 10%) Current consumption Max. 15mA Control output NPN open collector Load voltage ≤ 24VDC Load current Max. 50mA Residual voltage NPN: ≤1.2VDC, PNP: ≤ 1.2VDC Protection circuit Reverse polarity protection circuit, output overcurrent (short-circuit) protection circuit Insulation resistance ≥20 MΩ (250 VDC megger) Noise immunity The square wave noise (pulse width: 1㎲) by the noise simulator ±240VDC Dielectric strength 1,000VAC~ 50/60Hz for 1 minute Vibration 1.5mm amplitude (max. acceleration 196m/s²) at frequency of 10 to 2,000Hz in each X, Y, Z direction for 2 hours Shock 15,000 m/s² (approx. 1,500G) in each X, Y, Z direction for 3 times Environment_Ambient illumination Fluorescent lamp: Max. 1,000lx(received illumination) Environment_Ambient temperature -20 to 55℃, storage : -25 to 85℃ Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Protection structure IP50 (IEC standard) Connection Connector type Material Case: PBT, Sensing part: PC
$10.10
Autonics Autonics photoelectric micro sensor Through-beam type BS4-R2R-P
Sensing type Through-beam type Sensing distance 5mm Sensing target Opaque Min. sensing target ≥ 0.8 mm × 1.8 mm Hysteresis(distance) ≤0.05mm Response time Light ON: Max. 20㎲,Dark ON: Max. 80㎲ Response frequency 2kHz Light source Infrared LED Peak emission wavelength 940nm Operation mode Light ON/Dark ON(Built-in) Indicator Operation indicator (red LED) Weight ≈ 2.4 g Power voltage 5-24VDC ±10%(ripple P-P : max. 10%) Current consumption Max. 15mA Control output PNP open collector Load voltage ≤ 24VDC Load current Max. 50mA Residual voltage NPN: ≤1.2VDC, PNP: ≤ 1.2VDC Protection circuit Reverse polarity protection circuit, output overcurrent (short-circuit) protection circuit Insulation resistance ≥20 MΩ (250 VDC megger) Noise immunity The square wave noise (pulse width: 1㎲) by the noise simulator ±240VDC Dielectric strength 1,000VAC~ 50/60Hz for 1 minute Vibration 1.5mm amplitude (max. acceleration 196m/s²) at frequency of 10 to 2,000Hz in each X, Y, Z direction for 2 hours Shock 15,000 m/s² (approx. 1,500G) in each X, Y, Z direction for 3 times Environment_Ambient illumination Fluorescent lamp: Max. 1,000lx(received illumination) Environment_Ambient temperature -20 to 55℃, storage : -25 to 85℃ Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Protection structure IP50 (IEC standard) Connection Connector type Material Case: PBT, Sensing part: PC
$10.10
Autonics Autonics photoelectric micro sensor Through-beam type BS4-T2M-P
Sensing type Through-beam type Sensing distance 5mm Sensing target Opaque Min. sensing target ≥ 0.8 mm × 1.8 mm Hysteresis(distance) ≤0.05mm Response time Light ON: Max. 20㎲,Dark ON: Max. 80㎲ Response frequency 2kHz Light source Infrared LED Peak emission wavelength 940nm Operation mode Light ON/Dark ON(Built-in) Indicator Operation indicator (red LED) Weight ≈ 2.4 g Power voltage 5-24VDC ±10%(ripple P-P : max. 10%) Current consumption Max. 15mA Control output PNP open collector Load voltage ≤ 24VDC Load current Max. 50mA Residual voltage NPN: ≤1.2VDC, PNP: ≤ 1.2VDC Protection circuit Reverse polarity protection circuit, output overcurrent (short-circuit) protection circuit Insulation resistance ≥20 MΩ (250 VDC megger) Noise immunity The square wave noise (pulse width: 1㎲) by the noise simulator ±240VDC Dielectric strength 1,000VAC~ 50/60Hz for 1 minute Vibration 1.5mm amplitude (max. acceleration 196m/s²) at frequency of 10 to 2,000Hz in each X, Y, Z direction for 2 hours Shock 15,000 m/s² (approx. 1,500G) in each X, Y, Z direction for 3 times Environment_Ambient illumination Fluorescent lamp: Max. 1,000lx(received illumination) Environment_Ambient temperature -20 to 55℃, storage : -25 to 85℃ Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Protection structure IP50 (IEC standard) Connection Connector type Material Case: PBT, Sensing part: PC
$10.10
