Electrical & Automation

Sensing type Through-beam type Sensing distance 10m Sensing target Opaque material of min. Ø16mm Light source Infrared LED(850nm) Response time Max. 20ms Power voltage 24-240VAC~ ±10% 50/60Hz, 24-240VDC  ±10%(ripple P-P: max. 10%) Current consumption Emitter/Receiver: Max. 4VA Operation mode Light ON/Dark ON(set by switch) Control output Relay Connection type Cable type(Ø5, 2m) Environment_Ambient illumination Sunlight: Max. 11,000lx, Incandescent lamp: Max. 3,000lx (received illumination) Environment_Ambient temperature -20 to 65℃, storage: -25 to 70℃ Protection structure IP50 Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Material Case, Case cover: Heat resistant Acrylonitrile butadiene styrene,Sensing part: Polycarbonate(with polarizing filter: polymethyl methacrylate),Bracket: Steel Plate cold commercial, Bolt: steel chromium molybdenum,Nut: steel chromium molybden Accessories_Common Adjuster driver, Fixing bracket, Bolts, Nuts Weight Approx. 354g

Read more less

Sensing type Retroreflective type(standard type) Sensing distance 5m(MS-2) Sensing target Opaque material of min. Ø60mm Light source Infrared LED(940nm) Response time Max. 1ms Power voltage 12-24VDC  ±10%(ripple P-P: max. 10%) Current consumption Max. 50mA Sensitivity adjustment Sensitivity adjuster Operation mode Light ON/Dark ON(set by switch) Control output NPN, PNP open collector simultaneous output Connection type Cable type(Ø5, 2m) Environment_Ambient illumination Sunlight: Max. 11,000lx, Incandescent lamp: Max. 3,000lx (received illumination) Environment_Ambient temperature -20 to 65℃, storage: -25 to 70℃ Protection structure IP50 Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Material Case, Case cover: Heat resistant Acrylonitrile butadiene styrene,Sensing part: Polycarbonate(with polarizing filter: polymethyl methacrylate),Bracket: Steel Plate cold commercial, Bolt: steel chromium molybdenum,Nut: steel chromium molybden Accessories_Individual Reflector(MS-2) Accessories_Common Adjuster driver, Fixing bracket, Bolts, Nuts Weight Approx. 200g

Read more less

Sensing type Through-beam type Sensing distance 7m Sensing target Opaque material of min. Ø8mm Light source Red LED(650nm) Response time Max. 1ms Power voltage 12-24VDC  ±10%(ripple P-P: max. 10%) Current consumption Emitter/Receiver: Max. 20mA Sensitivity adjustment Sensitivity adjuster Operation mode Light ON/Dark ON(set by switch) Control output NPN open collector Connection type Cable type(Ø3.5, 2m) Environment_Ambient illumination Sunlight: Max. 11,000lx, Incandescent lamp: Max. 3,000lx (received illumination) Environment_Ambient temperature -25 to 55℃, storage: -40 to 70℃ Protection structure IP65 Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Material Case: Polycarbonate+Acrylonitrile butadiene styrene, LED Cap: Polycarbonate, Sensing part: Polymethyl methacrylate,Bracket: SUS304(steel use stainless 304), Bolt: Steel chromium molybdenum, Nut: Steel chromium molybdenum,Sleeve: Brass, Ni-plate Accessories_Common Fixing bracket, M3 Bolts: 4, M3 Nuts: 4, Adjuster driver Weight Approx. 115g (approx. 90g)

Read more less

Sensing type Retroreflective type Sensing distance 10~200mm Sensing target Opaque material of min. Ø27mm(min. sensing target: opaque material of Ø2mm) Light source Red LED(650nm) Response time Max. 1ms Power voltage 12-24VDC  ±10%(ripple P-P: max. 10%) Current consumption Max. 20mA Operation mode Light ON Control output NPN open collector Connection type Cable type(Ø2.5, 2m) Environment_Ambient illumination Sunlight: Max. 10,000lx, Incandescent lamp: Max. 3,000lx (received illumination) Environment_Ambient temperature -20 to 55℃, storage: -30 to 70℃ Protection structure IP67 Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Material Case: Polybutylene terephthalate, Sensing part: Polymethyl methacrylate, Bracket: Stainless steel 304,Bolt: Carbon steel wire for cold heading(SWCH10A) Weight Approx. 45g(approx. 25g)

Read more less

Sensing type Retroreflective type(built-in polarizing filter) Sensing distance 3m(MS-2A) Sensing target Opaque material of min. Ø75mm Light source Red LED(660nm) Response time Max. 1ms Power voltage 12-24VDC  ±10%(ripple P-P: max. 10%) Current consumption Max. 30mA Sensitivity adjustment Sensitivity adjuster Operation mode Light ON/Dark ON(set by switch) Control output NPN open collector Connection type Connector type(M8) Environment_Ambient illumination Sunlight: Max. 11,000lx, Incandescent lamp: Max. 3,000lx (received illumination) Environment_Ambient temperature -25 to 55℃, storage: -40 to 70℃ Protection structure IP67 Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Material Case: Polycarbonate+Acrylonitrile butadiene styrene, LED Cap: Polycarbonate, Sensing part: Polymethyl methacrylate,Bracket: SUS304(steel use stainless 304), Bolt: Steel chromium molybdenum, Nut: Steel chromium molybdenum,Sleeve: Brass, Ni-plate Accessories_Common Fixing bracket, M3 Bolts: 2, M3 Nuts: 2, Adjuster driver Accessories_Individual Reflector(MS-2A) Weight Approx. 55g (approx. 30g)

Read more less

PL-D2BDistance setting type Photoelectric Sensors - Distance setting type and bgs(Backgound suppression)function- Stable detection regardless object's color and material- Applicable in various fields with long detection distance(2m) Model PL-D2B Appearance Sensing method Distance - settable Sensing distance 0.2 ~ 2 m Detecting object White non-glossy paper (200x200 ㎜) Power voltage 12 - 24 V d.c. ±10 % Current consumption Max. 30 ㎃ Control output • NPN / PNP open collector asynchronously • Load current : max. 150 ㎃ d.c. (resistive load) • NPN residual voltage : max. 1 V d.c. • PNP residual voltage : max. 2 V d.c. Operation mode Light ON / Dark ON ※ Selectable by the mode V/R Response time Max. 2 ㎳. Hysteresis Less than 10% of the sensing distance Light source (wavelength) Infrared LED (880 nm) Receiving part 2 Photo diodes LED Indicator • Control out display : Red LED   • Stability display: Green LED Distance setting Near/Far : Optical distance adjusting volume 5 cycles. Protection circuit Reverse polarity protection and output short-circuit protection Ambient illumination • Sunlight: max. 11000 lx   • Incandescent lamp: max. 3000 lx Ambient temperature & humidity • Operation : -20 ~ 60 ℃   • Storage : -25 ~ 70 ℃, 35 ~ 85 % RH (without condensation) Degree of protection IP65 (IEC 60529) Insulation resistance Min. 20 MΩ. (500 V d.c. Mega) Dielectric strength 1,000 V a.c. (50/60 Hz for 1 min) Vibration resistance 10 - 55 Hz, double amplitude : 1.5mm for 2 hours each in X. Y and Z directions. Shock resistance 500 m/s² 3 times each in X. Y and Z directions Connection method • Cable output type   • Number of wires : 4P   • Thickness : Ø 4mm   • Length 2m Material • Case : PC   • Lens : PC Accessory Bracket, Adjustable driver, bolt, Nut. Approval

Read more less

Sensing type Through-beam type Sensing distance 10m Sensing target Opaque material of min. Ø12mm Light source Red LED(660nm) Response time Max. 1ms Power voltage 12-24VDC  ±10%(ripple P-P: max. 10%) Current consumption Emitter/Receiver: Max. 20mA Sensitivity adjustment Sensitivity adjuster Operation mode Light ON/Dark ON(set by switch) Control output NPN open collector Connection type Cable type(Ø3.5, 2m) Environment_Ambient illumination Sunlight: Max. 11,000lx, Incandescent lamp: Max. 3,000lx (received illumination) Environment_Ambient temperature -25 to 55℃, storage: -40 to 70℃ Protection structure IP65 Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Material Case: Polycarbonate+Acrylonitrile butadiene styrene, LED Cap: Polycarbonate, Sensing part: Polymethyl methacrylate,Bracket: SUS304(steel use stainless 304), Bolt: Steel chromium molybdenum, Nut: Steel chromium molybdenum,Sleeve: Brass, Ni-plate Accessories_Common Fixing bracket, M3 Bolts: 4, M3 Nuts: 4, Adjuster driver Weight Approx. 115g (approx. 90g)

Read more less

Sensing type Diffuse reflective type Sensing distance 5 to 30mm Sensing target Opaque, Translucent material(min. sensing target: Ø0.2mm) Light source Red LED(650nm) Response time Max. 1ms Power voltage 12-24VDC  ±10%(ripple P-P: max. 10%) Current consumption Max. 20mA Operation mode Light ON Control output PNP open collector Connection type Cable type(Ø2.5, 2m) Environment_Ambient illumination Sunlight: Max. 10,000lx, Incandescent lamp: Max. 3,000lx (received illumination) Environment_Ambient temperature -25 to 55℃, storage: -40 to 70℃ Protection structure IP67 Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Hysteresis(distance) Max. 20% at rated sensing distance Material Case: polybutylene terephthalate, sensing part: polymethyl methacrylate,bracket: SUS304(steel use stainless 304), bolt: carbon steel, sleeve: SUS304(steel use stainless 304) Accessories Fixing bracket, M2 bolt: 2 Weight Approx. 40g (approx. 25g)

Read more less

Sensing type Through-beam type Applicable pipe Using binding band: Ø6 to 13mm,Using protection bracket: Ø12.7mm (1/2 inch) transparent pipe in 1mm thickness (FEP (fluoroplastic) or with equivalent transparency) Standard sensing target Liquid in a pipe Light source Infrared LED(950nm) Response time Max. 2ms Power voltage 12-24VDC  ±10%(ripple P-P: max. 10%) Current consumption Max. 30mA Operation mode Light ON/Dark ON(set by button) Control output NPN open collector Connection type Cable type(Ø2.5, 1m) Environment_Ambient illumination Sunlight/Incandescent lamp: Max. 3,000lx for each(received illumination) Environment_Ambient temperature 10 to 55℃, storage: -25 to 65℃ Protection structure IP64 Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Material Case: Polycarbonate Accessories Binding band: 2, Anti-slip tube: 2 Weight Approx. 50g(approx. 13g)

Read more less

PB seriesGeneral Purpose Photoelectric Sensors - 25.4mm standard mounting hole- Hanyoung Nux new ASIC chip used (operation stability, long-distance detection)- Built-in VR for sensitivity adjustment- Convenient operation mode selection by VR- You can check the presence of overload with the output short circuit notification function- Excellent noise immunity and reduced disturbance of light influence- Strong protection circuit PB-R/D Model NPN PB-R01N PB-R04RN PB-R1N PB-D04N PNP PB-R01P PB-R04RP PB-R1P PB-D04P Sensing mode Diffuse-reflective Distancesettable Sensing distance 100 mm 400 mm 1 m 400 mm Hysteresis distance 20 % or less of detection distance Detecting object White non-glossy paper (100 x 100 mm) Light source (wavelength) IR (860nm) RED (640nm) IR (860nm) Current consumption Max. 30 mA Protection circuit Common ▪Power reverse connection protection, ▪Output reverse connection protection, ▪Output short-circuit over-current protection, ▪Output short-circuit alarm (Note 2) Individual Mutual interference prevention function Accessory Common Brackets A, volt (M3 X 12 mm), Volume driver Individual ─ Optional Brackets B, Brackets C, Mirror (HY-M5S) Weight Approximately 50g ■ Specification Power voltage 12 - 24 V d.c. ±10 % (Ripple max. 10 %) Control output NPN or PNP open collector output ▪Load current - max. 100 mA (26.4 V d.c. standard) ▪Residual voltage - NPN: max. 1 V, PNP : max. 1 V Operation mode Light ON / Dark ON switch Response time 1 ms or less Insulation Resistance More than 20 MΩ (500 V d.c. mega) Noise immunity Square wave noise by noise simulator (pulse width 1 μs) ± 240 V Dielectric strength 1,000 V a.c. (50/60 Hz for 1 minute) Vibration resistance 10 - 55 Hz, Double amplitude : 1.5 mm, X·Y·Z 2 in each direction for 2 hours Shock resistance 500 m/s², X·Y·Z each direction 3 times Ambient illumination ▪Sunlight : max. 11,000 lx / Incandescent : max 3,000 lx Ambient temperature ▪During operation : -25 ~ +55 ℃, During storage : -40 ~ +70 ℃ (Without condensation or icing) Ambient humidity ▪35 ~ 85 % RH (Without condensation) Degree of protection IP65 (IEC standard) Certification Material Case PBT GF30 % Display PC Lens PC

Read more less

Sensing type Diffuse reflective type Sensing distance 100mm Sensing target Opaque, Translucent material Response time Operation: Max. 3ms, Return: Max. 100ms Light source Infrared LED Sensitivity adjustment Sensitivity adjuster Operation mode Light ON Weight Approx. 75g(approx. 38g) Power voltage 12-24VDC  ±10%(ripple P-P: max. 10%) Current consumption Max. 35mA Control output NPN open collector Environment_Ambient illumination Sunlight: Max. 11,000lx, Incandescent lamp: Max. 3,000lx (received illumination) Environment_Ambient temperature -20 to 65℃, storage: -25 to 70℃ Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Protection structure IP50 Connection type Cable type(Ø3.5, 2m) Material Case: PC, sensing part: PC, bracket: SPCC, bolt: SCM, nut: SCM, sleeve: Brass, Ni-plate

Read more less

Sensing type Convergent reflective type Sensing distance 5 to 30mm Sensing target Opaque, Translucent material(min. sensing target: Ø0.15mm) Light source Red LED(650nm) Response time Max. 1ms Power voltage 12-24VDC  ±10%(ripple P-P: max. 10%) Current consumption Max. 20mA Operation mode Light ON Control output NPN open collector Connection type Cable type(Ø2.5, 2m) Environment_Ambient illumination Sunlight: Max. 10,000lx, Incandescent lamp: Max. 3,000lx (received illumination) Environment_Ambient temperature -20 to 55℃, storage: -30 to 70℃ Protection structure IP67 Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Hysteresis(distance) Max. 15% of maximum sensing distance Material Case: Polybutylene terephthalate, Sensing part: Polymethyl methacrylate, Bracket: Stainless steel 304,Bolt: Carbon steel wire for cold heading(SWCH10A) Weight Approx. 45g(approx. 25g)

Read more less

Sensing type Retroreflective type(built-in polarizing filter) Sensing distance 3m(MS-2A) Sensing target Opaque material of min. Ø75mm Light source Red LED(660nm) Response time Max. 1ms Power voltage 12-24VDC  ±10%(ripple P-P: max. 10%) Current consumption Max. 30mA Sensitivity adjustment Sensitivity adjuster Operation mode Light ON/Dark ON(set by switch) Control output NPN open collector Connection type Cable type(Ø3.5, 2m) Environment_Ambient illumination Sunlight: Max. 11,000lx, Incandescent lamp: Max. 3,000lx (received illumination) Environment_Ambient temperature -25 to 55℃, storage: -40 to 70℃ Protection structure IP65 Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Material Case: Polycarbonate+Acrylonitrile butadiene styrene, LED Cap: Polycarbonate, Sensing part: Polymethyl methacrylate,Bracket: SUS304(steel use stainless 304), Bolt: Steel chromium molybdenum, Nut: Steel chromium molybdenum,Sleeve: Brass, Ni-plate Accessories_Common Fixing bracket, M3 Bolts: 2, M3 Nuts: 2, Adjuster driver Accessories_Individual Reflector(MS-2A) Weight Approx. 85g (approx. 60g)

Read more less

Sensing type Retroreflective type(standard type) Sensing distance 5m(MS-2) Sensing target Opaque material of min. Ø60mm Light source Infrared LED(940nm) Response time Max. 20ms Power voltage 24-240VAC~ ±10% 50/60Hz, 24-240VDC  ±10%(ripple P-P: max. 10%) Current consumption Max. 4VA Sensitivity adjustment Sensitivity adjuster Operation mode Light ON/Dark ON(set by switch) Control output Relay Connection type Cable type(Ø5, 2m) Environment_Ambient illumination Sunlight: Max. 11,000lx, Incandescent lamp: Max. 3,000lx (received illumination) Environment_Ambient temperature -20 to 65℃, storage: -25 to 70℃ Protection structure IP50 Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Material Case, Case cover: Heat resistant Acrylonitrile butadiene styrene,Sensing part: Polycarbonate(with polarizing filter: polymethyl methacrylate),Bracket: Steel Plate cold commercial, Bolt: steel chromium molybdenum,Nut: steel chromium molybden Accessories_Individual Reflector(MS-2) Accessories_Common Adjuster driver, Fixing bracket, Bolts, Nuts Weight Approx. 208g

Read more less

Sensing type Through-beam type Sensing distance 1m Sensing target Opaque material of min. Ø2mm Light source Red LED(650nm) Response time Max. 1ms Power voltage 12-24VDC  ±10%(ripple P-P: max. 10%) Current consumption Emitter/Receiver: Max. 20mA Operation mode Dark ON Control output NPN open collector Connection type Cable type(Ø2.5, 2m) Environment_Ambient illumination Sunlight: Max. 10,000lx, Incandescent lamp: Max. 3,000lx (received illumination) Environment_Ambient temperature -20 to 55℃, storage: -30 to 70℃ Protection structure IP67 Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Material Case: Polybutylene terephthalate, Sensing part: Polymethyl methacrylate, Bracket: Stainless steel 304,Bolt: Carbon steel wire for cold heading(SWCH10A) Weight Approx. 65g(approx. 40g)

Read more less

Sensing type Diffuse reflective type Sensing distance 200mm Sensing target Opaque, Translucent material Light source Infrared LED(940nm) Response time Max. 3ms Power voltage 12-24VDC  ±10%(ripple P-P: max. 10%) Current consumption Max. 40mA Sensitivity adjustment Sensitivity adjuster Operation mode Light ON(option: Dark ON) Control output NPN open collector Connection type Cable type(Ø4, 2m) Environment_Ambient illumination Sunlight: Max. 11,000lx, Incandescent lamp: Max. 3,000lx (received illumination) Environment_Ambient temperature -10 to 60℃, storage: -25 to 70℃ Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Hysteresis(distance) Max. 10% at sensing distance Material Case: Acrylonitrile butadiene styrene, Sensing part: Acryl, Bracket: Steel plate cold commercial, Bolt: Steel chromium molybdenum, Nut: Steel chromium molybdenum Unit weight (packaged weight) ≈ 88 g (≈ 156 g)

Read more less

Sensing type Diffuse reflective type Sensing distance 1m Sensing target Opaque, Translucent material Light source Infrared LED(850nm) Response time Max. 1ms Power voltage 12-24VDC  ±10%(ripple P-P: max. 10%) Current consumption Max. 30mA Sensitivity adjustment Sensitivity adjuster Operation mode Light ON/Dark ON(set by switch) Control output NPN open collector Connection type Cable type(Ø3.5, 2m) Environment_Ambient illumination Sunlight: Max. 11,000lx, Incandescent lamp: Max. 3,000lx (received illumination) Environment_Ambient temperature -25 to 55℃, storage: -40 to 70℃ Protection structure IP65 Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Hysteresis(distance) Max. 20% of sensing distance Material Case: Polycarbonate+Acrylonitrile butadiene styrene, LED Cap: Polycarbonate, Sensing part: Polymethyl methacrylate,Bracket: SUS304(steel use stainless 304), Bolt: Steel chromium molybdenum, Nut: Steel chromium molybdenum,Sleeve: Brass, Ni-plate Accessories_Common Fixing bracket, M3 Bolts: 2, M3 Nuts: 2, Adjuster driver Weight Approx. 70g (approx. 45g)

Read more less

Sensing type Diffuse reflective type Sensing distance 300mm Sensing target Opaque, Translucent material Light source Red LED(660nm) Response time Max. 1ms Power voltage 12-24VDC  ±10%(ripple P-P: max. 10%) Current consumption Max. 30mA Sensitivity adjustment Sensitivity adjuster Operation mode Light ON/Dark ON(set by switch) Control output NPN open collector Connection type Cable type(Ø3.5, 2m) Environment_Ambient illumination Sunlight: Max. 11,000lx, Incandescent lamp: Max. 3,000lx (received illumination) Environment_Ambient temperature -25 to 55℃, storage: -40 to 70℃ Protection structure IP65 Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Hysteresis(distance) Max. 20% of sensing distance Material Case: Polycarbonate+Acrylonitrile butadiene styrene, LED Cap: Polycarbonate, Sensing part: Polymethyl methacrylate,Bracket: SUS304(steel use stainless 304), Bolt: Steel chromium molybdenum, Nut: Steel chromium molybdenum,Sleeve: Brass, Ni-plate Accessories_Common Fixing bracket, M3 Bolts: 2, M3 Nuts: 2, Adjuster driver Weight Approx. 70g (approx. 45g)

Read more less

Sensing type Diffuse reflective type Sensing distance 300mm Sensing target Opaque, Translucent material Light source Infrared LED(940nm) Response time Max. 1ms Power voltage 12-24VDC  ±10%(ripple P-P: max. 10%) Current consumption Max. 50mA Sensitivity adjustment Sensitivity adjuster Operation mode Light ON/Dark ON(set by switch) Control output NPN, PNP open collector simultaneous output Connection type Cable type(Ø5, 2m) Environment_Ambient illumination Sunlight: Max. 11,000lx, Incandescent lamp: Max. 3,000lx (received illumination) Environment_Ambient temperature -20 to 65℃, storage: -25 to 70℃ Protection structure IP50 Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Hysteresis(distance) Max. 20% at sensing distance Material Case, Case cover: Heat resistant Acrylonitrile butadiene styrene,Sensing part: Polycarbonate(with polarizing filter: polymethyl methacrylate),Bracket: Steel Plate cold commercial, Bolt: steel chromium molybdenum,Nut: steel chromium molybden Accessories_Common Adjuster driver, Fixing bracket, Bolts, Nuts Weight Approx. 187g

Read more less

Sensing type Diffuse reflective type Sensing distance 5 to 30mm Sensing target Opaque, Translucent material(min. sensing target: Ø0.2mm) Light source Red LED(650nm) Response time Max. 1ms Power voltage 12-24VDC  ±10%(ripple P-P: max. 10%) Current consumption Max. 20mA Operation mode Light ON Control output NPN open collector Connection type Cable type(Ø2.5, 2m) Environment_Ambient illumination Sunlight: Max. 10,000lx, Incandescent lamp: Max. 3,000lx (received illumination) Environment_Ambient temperature -25 to 55℃, storage: -40 to 70℃ Protection structure IP67 Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Hysteresis(distance) Max. 20% at rated sensing distance Material Case: polybutylene terephthalate, sensing part: polymethyl methacrylate,bracket: SUS304(steel use stainless 304), bolt: carbon steel, sleeve: SUS304(steel use stainless 304) Accessories Fixing bracket, M2 bolt: 2 Weight Approx. 40g (approx. 25g)

Read more less

Sensing type Diffuse reflective type Sensing distance 300mm Sensing target Opaque, Translucent material Light source Infrared LED(940nm) Response time Max. 20ms Power voltage 24-240VAC~ ±10% 50/60Hz, 24-240VDC  ±10%(ripple P-P: max. 10%) Current consumption Max. 4VA Sensitivity adjustment Sensitivity adjuster Operation mode Light ON/Dark ON(set by switch) Control output Relay Connection type Cable type(Ø5, 2m) Environment_Ambient illumination Sunlight: Max. 11,000lx, Incandescent lamp: Max. 3,000lx (received illumination) Environment_Ambient temperature -20 to 65℃, storage: -25 to 70℃ Protection structure IP50 Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Hysteresis(distance) Max. 20% at sensing distance Material Case, Case cover: Heat resistant Acrylonitrile butadiene styrene,Sensing part: Polycarbonate(with polarizing filter: polymethyl methacrylate),Bracket: Steel Plate cold commercial, Bolt: steel chromium molybdenum,Nut: steel chromium molybden Accessories_Common Adjuster driver, Fixing bracket, Bolts, Nuts Weight Approx. 195g

Read more less

Sensing type Through-beam type Sensing distance 3m Sensing target Opaque material of min. Ø6mm Response time Max. 1ms Light source Infrared LED Operation mode Dark ON Weight Approx. 105g(approx. 80g) Power voltage 12-24VDC  ±10%(ripple P-P: max. 10%) Current consumption Emitter/Receiver: Max. 30mA Control output NPN open collector Environment_Ambient illumination Sunlight: Max. 11,000lx, Incandescent lamp: Max. 3,000lx (received illumination) Environment_Ambient temperature -20 to 65℃, storage: -25 to 70℃ Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Protection structure IP64 Connection type Cable type(Ø3.5, 2m) Material Case: PC, sensing part: PC, bracket: SPCC, bolt: SCM, nut: SCM, sleeve: Brass, Ni-plate

Read more less

Sensing type Diffuse reflective type Sensing distance 2m Sensing target Opaque, Translucent material Light source Infrared LED(850nm) Response time Max. 1ms Power voltage 12-24VDC  ±10%(ripple P-P: max. 10%) Current consumption Max. 15mA Sensitivity adjustment Sensitivity adjuster Operation mode Light ON Control output NPN open collector Connection type Cable type(Ø3, 2m) Environment_Ambient illumination Sunlight: Max. 11,000lx, Incandescent lamp: Max. 3,000lx (received illumination) Environment_Ambient temperature -25 to 55℃, storage: -25 to 70℃ Protection structure IP64 Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Hysteresis(distance) Max. 20% at sensing distance Material Case: Acrylonitrile butadiene styrene, Sensing part: Polycarbonate, Indicator: Polycarbonate, Adjuster: IXEF Accessories Adjuster driver Weight Approx. 50g

Read more less

Sensing type Through-beam type Sensing distance 1m Sensing target Opaque material of min. Ø2mm Light source Red LED(650nm) Response time Max. 1ms Power voltage 12-24VDC  ±10%(ripple P-P: max. 10%) Current consumption Emitter/Receiver: Max. 20mA Operation mode Light ON Control output NPN open collector Connection type Cable type(Ø2.5, 2m) Environment_Ambient illumination Sunlight: Max. 10,000lx, Incandescent lamp: Max. 3,000lx (received illumination) Environment_Ambient temperature -25 to 55℃, storage: -40 to 70℃ Protection structure IP67 Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Material Case: polybutylene terephthalate, sensing part: polymethyl methacrylate,bracket: SUS304(steel use stainless 304), bolt: carbon steel, sleeve: SUS304(steel use stainless 304) Accessories Fixing bracket, M2 bolt: 4 Weight Approx. 70g (approx. 40g)

Read more less

Sensing type Through-beam type Sensing distance 1m Sensing target Opaque material of min. Ø2mm Light source Red LED(650nm) Response time Max. 1ms Power voltage 12-24VDC  ±10%(ripple P-P: max. 10%) Current consumption Emitter/Receiver: Max. 20mA Operation mode Dark ON Control output NPN open collector Connection type Cable type(Ø2.5, 2m) Environment_Ambient illumination Sunlight: Max. 10,000lx, Incandescent lamp: Max. 3,000lx (received illumination) Environment_Ambient temperature -25 to 55℃, storage: -40 to 70℃ Protection structure IP67 Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Material Case: polybutylene terephthalate, sensing part: polymethyl methacrylate,bracket: SUS304(steel use stainless 304), bolt: carbon steel, sleeve: SUS304(steel use stainless 304) Accessories Fixing bracket, M2 bolt: 4 Weight Approx. 70g (approx. 40g)

Read more less

Sensing type Diffuse reflective type Sensing distance 100mm Sensing target Opaque, Translucent material Light source Infrared LED(850nm) Response time Max. 1ms Power voltage 10-30VDC  ±10%(ripple P-P: max. 10%) Current consumption Max. 30mA Sensitivity adjustment Sensitivity adjuster Operation mode Light ON/Dark ON(set by control wire) Control output NPN open collector Connection type Cable type(Ø4, 2m) Environment_Ambient illumination Sunlight: Max. 11,000lx, Incandescent lamp: Max. 3,000lx (received illumination) Environment_Ambient temperature -25 to 60℃, storage: -30 to 70℃ Protection structure IP67(IEC standard) Environment_Ambient humidity 35 to 85% RH, storage: 35 to 85% RH Hysteresis(distance) Max. 20% at rated sensing distance Material ㆍCase: brass, Ni-plateㆍLens, Lens cover: polymethyl methacrylate acrylic Weight Approx. 150g(approx. 70g)

Read more less

Data sheet Installation Non-flush Sensing side diameter Ø8mm Sensing distance 2mm Hysteresis(distance) Max. 10% of sensing distance Standard sensing target 8×8×1mm(iron) Response frequency 1kHz Indicator Operation indicator (red LED) Unit weight (packaged weight) ≈ 52 g (≈ 64 g) Power voltage 12 - 24 VDC(ripple P-P: ≤ 10 %), operating voltage: 10 - 30 VDC Current specification Leakage current: Max. 0.6mA Control output 2 to 100 mA Residual voltage Max. 3.5V Protection circuit Surge protection circuit, output short over current protection circuit, reverse polarity protection circuit Insulation resistance ≥ 50 MΩ (500 VDC megger) Dielectric strength Between the charging part and the case: 1,500 VAC~ 50 / 60Hz for 1 min Vibration 1.0 mm amplitude at frequency of 10 to 55 Hzin each X, Y, Z direction for 2 hours Shock 500 m/s² (≈ 50 G) in each X, Y, Z direction for 3 times Environment_Ambient temperature -25 to 70 ℃, storage: -30 to 80 ℃ (no freezing or condensation) Environment_Ambient humidity 35 to 95 %RH, storage: 35 to 95 %RH (no freezing or condensation) Protection structure IP67(IEC standard) Connection Cable type Cable Standard/material Standard type cable (black): polyvinyl chloride (PVC) Material Case/Nut: nickel plated brass (DIA. of sensing side Ø 8 mm connector type case: SUS303), washer: nickel plated iron, sensing side: PBT ※The response frequency is the average value. The standard sensing target is used and the width is set as 2 times of the standard sensing target, 1/2 of the sensing distance for the distance.※Check the condition of connected device.

Read more less

Data sheet  Installation Flush Sensing side diameter Ø30mm Sensing distance 10mm Hysteresis(distance) Max. 10% of sensing distance Standard sensing target 30×30×1mm(iron) Response frequency 400Hz Indicator Operation indicator (red LED) Unit weight (packaged weight) ≈ 170 g (≈ 207 g) Power voltage 12 - 24 VDC(ripple P-P: ≤ 10 %), operating voltage: 10 - 30 VDC Current specification Current consumption: Max. 10mA Control output ≤ 200 mA Residual voltage Max. 1.5V Protection circuit Surge protection circuit, output short over current protection circuit, reverse polarity protection circuit Insulation resistance ≥ 50 MΩ (500 VDC megger) Dielectric strength Between the charging part and the case: 1,500 VAC~ 50 / 60Hz for 1 min Vibration 1.0 mm amplitude at frequency of 10 to 55 Hzin each X, Y, Z direction for 2 hours Shock 500 m/s² (≈ 50 G) in each X, Y, Z direction for 3 times Environment_Ambient temperature -25 to 70 ℃, storage: -30 to 80 ℃ (no freezing or condensation) Environment_Ambient humidity 35 to 95 %RH, storage: 35 to 95 %RH (no freezing or condensation) Protection structure IP67(IEC standard) Connection Cable type Cable Standard/material Standard type cable (black): polyvinyl chloride (PVC) Material Case/Nut: nickel plated brass (DIA. of sensing side Ø 8 mm connector type case: SUS303), washer: nickel plated iron, sensing side: PBT ※The response frequency is the average value. The standard sensing target is used and the width is set as 2 times of the standard sensing target, 1/2 of the sensing distance for the distance.

Read more less

Installation Flush Sensing side diameter Ø30mm Sensing distance 10mm Hysteresis(distance) Max. 10% of sensing distance Standard sensing target 30×30×1mm(iron) Response frequency 400Hz Indicator Operation indicator (red LED) Unit weight (packaged weight) ≈ 170 g (≈ 207 g) Power voltage 12 - 24 VDC(ripple P-P: ≤ 10 %), operating voltage: 10 - 30 VDC Current specification Current consumption: Max. 10mA Control output ≤ 200 mA Residual voltage Max. 1.5V Protection circuit Surge protection circuit, output short over current protection circuit, reverse polarity protection circuit Insulation resistance ≥ 50 MΩ (500 VDC megger) Dielectric strength Between the charging part and the case: 1,500 VAC~ 50 / 60Hz for 1 min Vibration 1.0 mm amplitude at frequency of 10 to 55 Hzin each X, Y, Z direction for 2 hours Shock 500 m/s² (≈ 50 G) in each X, Y, Z direction for 3 times Environment_Ambient temperature -25 to 70 ℃, storage: -30 to 80 ℃ (no freezing or condensation) Environment_Ambient humidity 35 to 95 %RH, storage: 35 to 95 %RH (no freezing or condensation) Protection structure IP67(IEC standard) Connection Cable type Cable Standard/material Standard type cable (black): polyvinyl chloride (PVC) Material Case/Nut: nickel plated brass (DIA. of sensing side Ø 8 mm connector type case: SUS303), washer: nickel plated iron, sensing side: PBT ※The response frequency is the average value. The standard sensing target is used and the width is set as 2 times of the standard sensing target, 1/2 of the sensing distance for the distance.

Read more less

Industrial proximity se Installation Flush Sensing side diameter Ø30mm Sensing distance 10mm Hysteresis(distance) Max. 10% of sensing distance Standard sensing target 30×30×1mm(iron) Response frequency 400Hz Indicator Operation indicator (red LED) Unit weight (packaged weight) ≈ 210 g (≈ 247 g) Power voltage 12 - 24 VDC(ripple P-P: ≤ 10 %), operating voltage: 10 - 30 VDC Current specification Current consumption: Max. 10mA Control output ≤ 200 mA Residual voltage Max. 1.5V Protection circuit Surge protection circuit, output short over current protection circuit, reverse polarity protection circuit Insulation resistance ≥ 50 MΩ (500 VDC megger) Dielectric strength Between the charging part and the case: 1,500 VAC~ 50 / 60Hz for 1 min Vibration 1.0 mm amplitude at frequency of 10 to 55 Hzin each X, Y, Z direction for 2 hours Shock 500 m/s² (≈ 50 G) in each X, Y, Z direction for 3 times Environment_Ambient temperature -25 to 70 ℃, storage: -30 to 80 ℃ (no freezing or condensation) Environment_Ambient humidity 35 to 95 %RH, storage: 35 to 95 %RH (no freezing or condensation) Protection structure IP67(IEC standard) Connection Cable type Cable Standard/material Standard type cable (black): polyvinyl chloride (PVC) Material Case/Nut: nickel plated brass (DIA. of sensing side Ø 8 mm connector type case: SUS303), washer: nickel plated iron, sensing side: PBT nsor for automation systems.

Read more less

au Installation Flush Sensing side diameter Ø30mm Sensing distance 10mm Hysteresis(distance) Max. 10% of sensing distance Standard sensing target 30×30×1mm(iron) Response frequency 400Hz Indicator Operation indicator (red LED) Unit weight (packaged weight) ≈ 210 g (≈ 247 g) Power voltage 12 - 24 VDC(ripple P-P: ≤ 10 %), operating voltage: 10 - 30 VDC Current specification Current consumption: Max. 10mA Control output ≤ 200 mA Residual voltage Max. 1.5V Protection circuit Surge protection circuit, output short over current protection circuit, reverse polarity protection circuit Insulation resistance ≥ 50 MΩ (500 VDC megger) Dielectric strength Between the charging part and the case: 1,500 VAC~ 50 / 60Hz for 1 min Vibration 1.0 mm amplitude at frequency of 10 to 55 Hzin each X, Y, Z direction for 2 hours Shock 500 m/s² (≈ 50 G) in each X, Y, Z direction for 3 times Environment_Ambient temperature -25 to 70 ℃, storage: -30 to 80 ℃ (no freezing or condensation) Environment_Ambient humidity 35 to 95 %RH, storage: 35 to 95 %RH (no freezing or condensation) Protection structure IP67(IEC standard) Connection Cable type Cable Standard/material Standard type cable (black): polyvinyl chloride (PVC) Material Case/Nut: nickel plated brass (DIA. of sensing side Ø 8 mm connector type case: SUS303), washer: nickel plated iron, sensing side: PBT al proximity sensor for automation systems.

Read more less

Installation Non-flush Sensing side diameter Ø30mm Sensing distance 15mm Hysteresis(distance) Max. 10% of sensing distance Standard sensing target 45×45×1mm(iron) Response frequency 200Hz Indicator Operation indicator (red LED) Unit weight (packaged weight) ≈ 170 g (≈ 207 g) Power voltage 12 - 24 VDC(ripple P-P: ≤ 10 %), operating voltage: 10 - 30 VDC Current specification Current consumption: Max. 10mA Control output ≤ 200 mA Residual voltage Max. 1.5V Protection circuit Surge protection circuit, output short over current protection circuit, reverse polarity protection circuit Insulation resistance ≥ 50 MΩ (500 VDC megger) Dielectric strength Between the charging part and the case: 1,500 VAC~ 50 / 60Hz for 1 min Vibration 1.0 mm amplitude at frequency of 10 to 55 Hzin each X, Y, Z direction for 2 hours Shock 500 m/s² (≈ 50 G) in each X, Y, Z direction for 3 times Environment_Ambient temperature -25 to 70 ℃, storage: -30 to 80 ℃ (no freezing or condensation) Environment_Ambient humidity 35 to 95 %RH, storage: 35 to 95 %RH (no freezing or condensation) Protection structure IP67(IEC standard) Connection Cable type Cable Standard/material Standard type cable (black): polyvinyl chloride (PVC) Material Case/Nut: nickel plated brass (DIA. of sensing side Ø 8 mm connector type case: SUS303), washer: nickel plated iron, sensing side: PBT

Read more less

Installation Non-flush Sensing side diameter Ø30mm Sensing distance 15mm Hysteresis(distance) Max. 10% of sensing distance Standard sensing target 45×45×1mm(iron) Response frequency 200Hz Indicator Operation indicator (red LED) Unit weight (packaged weight) ≈ 170 g (≈ 207 g) Power voltage 12 - 24 VDC(ripple P-P: ≤ 10 %), operating voltage: 10 - 30 VDC Current specification Current consumption: Max. 10mA Control output ≤ 200 mA Residual voltage Max. 1.5V Protection circuit Surge protection circuit, output short over current protection circuit, reverse polarity protection circuit Insulation resistance ≥ 50 MΩ (500 VDC megger) Dielectric strength Between the charging part and the case: 1,500 VAC~ 50 / 60Hz for 1 min Vibration 1.0 mm amplitude at frequency of 10 to 55 Hzin each X, Y, Z direction for 2 hours Shock 500 m/s² (≈ 50 G) in each X, Y, Z direction for 3 times Environment_Ambient temperature -25 to 70 ℃, storage: -30 to 80 ℃ (no freezing or condensation) Environment_Ambient humidity 35 to 95 %RH, storage: 35 to 95 %RH (no freezing or condensation) Protection structure IP67(IEC standard) Connection Cable type Cable Standard/material Standard type cable (black): polyvinyl chloride (PVC) Material Case/Nut: nickel plated brass (DIA. of sensing side Ø 8 mm connector type case: SUS303), washer: nickel plated iron, sensing side: PBT

Read more less

Installation Non-flush Sensing side diameter Ø30mm Sensing distance 15mm Hysteresis(distance) Max. 10% of sensing distance Standard sensing target 45×45×1mm(iron) Response frequency 200Hz Indicator Operation indicator (red LED) Unit weight (packaged weight) ≈ 210 g (≈ 247 g) Power voltage 12 - 24 VDC(ripple P-P: ≤ 10 %), operating voltage: 10 - 30 VDC Current specification Current consumption: Max. 10mA Control output ≤ 200 mA Residual voltage Max. 1.5V Protection circuit Surge protection circuit, output short over current protection circuit, reverse polarity protection circuit Insulation resistance ≥ 50 MΩ (500 VDC megger) Dielectric strength Between the charging part and the case: 1,500 VAC~ 50 / 60Hz for 1 min Vibration 1.0 mm amplitude at frequency of 10 to 55 Hzin each X, Y, Z direction for 2 hours Shock 500 m/s² (≈ 50 G) in each X, Y, Z direction for 3 times Environment_Ambient temperature -25 to 70 ℃, storage: -30 to 80 ℃ (no freezing or condensation) Environment_Ambient humidity 35 to 95 %RH, storage: 35 to 95 %RH (no freezing or condensation) Protection structure IP67(IEC standard) Connection Cable type Cable Standard/material Standard type cable (black): polyvinyl chloride (PVC) Material Case/Nut: nickel plated brass (DIA. of sensing side Ø 8 mm connector type case: SUS303), washer: nickel plated iron, sensing side: PBT

Read more less

Installation Non-flush Sensing side diameter Ø30mm Sensing distance 15mm Hysteresis(distance) Max. 10% of sensing distance Standard sensing target 45×45×1mm(iron) Response frequency 200Hz Indicator Operation indicator (red LED) Unit weight (packaged weight) ≈ 210 g (≈ 247 g) Power voltage 12 - 24 VDC(ripple P-P: ≤ 10 %), operating voltage: 10 - 30 VDC Current specification Current consumption: Max. 10mA Control output ≤ 200 mA Residual voltage Max. 1.5V Protection circuit Surge protection circuit, output short over current protection circuit, reverse polarity protection circuit Insulation resistance ≥ 50 MΩ (500 VDC megger) Dielectric strength Between the charging part and the case: 1,500 VAC~ 50 / 60Hz for 1 min Vibration 1.0 mm amplitude at frequency of 10 to 55 Hzin each X, Y, Z direction for 2 hours Shock 500 m/s² (≈ 50 G) in each X, Y, Z direction for 3 times Environment_Ambient temperature -25 to 70 ℃, storage: -30 to 80 ℃ (no freezing or condensation) Environment_Ambient humidity 35 to 95 %RH, storage: 35 to 95 %RH (no freezing or condensation) Protection structure IP67(IEC standard) Connection Cable type Cable Standard/material Standard type cable (black): polyvinyl chloride (PVC) Material Case/Nut: nickel plated brass (DIA. of sensing side Ø 8 mm connector type case: SUS303), washer: nickel plated iron, sensing side: PBT

Read more less

Installation Flush Sensing side diameter Ø12mm Sensing distance 2mm Hysteresis(distance) Max. 10% of sensing distance Standard sensing target 12×12×1mm(iron) Response frequency 1.5kHz Indicator Operation indicator (red LED) Unit weight (packaged weight) ≈ 72 g (≈ 84 g) Power voltage 12 - 24 VDC(ripple P-P: ≤ 10 %), operating voltage: 10 - 30 VDC Current specification Current consumption: Max. 10mA Control output ≤ 200 mA Residual voltage Max. 1.5V Protection circuit Surge protection circuit, output short over current protection circuit, reverse polarity protection circuit Insulation resistance ≥ 50 MΩ (500 VDC megger) Dielectric strength Between the charging part and the case: 1,500 VAC~ 50 / 60Hz for 1 min Vibration 1.0 mm amplitude at frequency of 10 to 55 Hzin each X, Y, Z direction for 2 hours Shock 500 m/s² (≈ 50 G) in each X, Y, Z direction for 3 times Environment_Ambient temperature -25 to 70 ℃, storage: -30 to 80 ℃ (no freezing or condensation) Environment_Ambient humidity 35 to 95 %RH, storage: 35 to 95 %RH (no freezing or condensation) Protection structure IP67(IEC standard) Connection Cable type Cable Standard/material Standard type cable (black): polyvinyl chloride (PVC) Material Case/Nut: nickel plated brass (DIA. of sensing side Ø 8 mm connector type case: SUS303), washer: nickel plated iron, sensing side: PBT

Read more less

Installation Non-flush Sensing side diameter Ø12mm Sensing distance 4mm Hysteresis(distance) Max. 10% of sensing distance Standard sensing target 12×12×1mm(iron) Response frequency 500Hz Indicator Operation indicator (red LED) Unit weight (packaged weight) ≈ 70 g (≈ 82 g) Power voltage 12 - 24 VDC(ripple P-P: ≤ 10 %), operating voltage: 10 - 30 VDC Current specification Current consumption: Max. 10mA Control output ≤ 200 mA Residual voltage Max. 1.5V Protection circuit Surge protection circuit, output short over current protection circuit, reverse polarity protection circuit Insulation resistance ≥ 50 MΩ (500 VDC megger) Dielectric strength Between the charging part and the case: 1,500 VAC~ 50 / 60Hz for 1 min Vibration 1.0 mm amplitude at frequency of 10 to 55 Hzin each X, Y, Z direction for 2 hours Shock 500 m/s² (≈ 50 G) in each X, Y, Z direction for 3 times Environment_Ambient temperature -25 to 70 ℃, storage: -30 to 80 ℃ (no freezing or condensation) Environment_Ambient humidity 35 to 95 %RH, storage: 35 to 95 %RH (no freezing or condensation) Protection structure IP67(IEC standard) Connection Cable type Cable Standard/material Standard type cable (black): polyvinyl chloride (PVC) Material Case/Nut: nickel plated brass (DIA. of sensing side Ø 8 mm connector type case: SUS303), washer: nickel plated iron, sensing side: PBT

Read more less

Installation Non-flush Sensing side diameter Ø12mm Sensing distance 4mm Hysteresis(distance) Max. 10% of sensing distance Standard sensing target 12×12×1mm(iron) Response frequency 500Hz Indicator Operation indicator (red LED) Unit weight (packaged weight) ≈ 70 g (≈ 82 g) Power voltage 12 - 24 VDC(ripple P-P: ≤ 10 %), operating voltage: 10 - 30 VDC Current specification Current consumption: Max. 10mA Control output ≤ 200 mA Residual voltage Max. 1.5V Protection circuit Surge protection circuit, output short over current protection circuit, reverse polarity protection circuit Insulation resistance ≥ 50 MΩ (500 VDC megger) Dielectric strength Between the charging part and the case: 1,500 VAC~ 50 / 60Hz for 1 min Vibration 1.0 mm amplitude at frequency of 10 to 55 Hzin each X, Y, Z direction for 2 hours Shock 500 m/s² (≈ 50 G) in each X, Y, Z direction for 3 times Environment_Ambient temperature -25 to 70 ℃, storage: -30 to 80 ℃ (no freezing or condensation) Environment_Ambient humidity 35 to 95 %RH, storage: 35 to 95 %RH (no freezing or condensation) Protection structure IP67(IEC standard) Connection Cable type Cable Standard/material Standard type cable (black): polyvinyl chloride (PVC) Material Case/Nut: nickel plated brass (DIA. of sensing side Ø 8 mm connector type case: SUS303), washer: nickel plated iron, sensing side: PBT

Read more less

Installation Flush Sensing side diameter Ø8mm Sensing distance 1.5mm Hysteresis(distance) Max. 10% of sensing distance Standard sensing target 8×8×1mm(iron) Response frequency 1.5kHz Indicator Operation indicator (red LED) Unit weight (packaged weight) ≈ 54 g (≈ 66 g) Power voltage 12 - 24 VDC(ripple P-P: ≤ 10 %), operating voltage: 10 - 30 VDC Current specification Current consumption: Max. 10mA Control output ≤ 200 mA Residual voltage Max. 2V Protection circuit Surge protection circuit, output short over current protection circuit, reverse polarity protection circuit Insulation resistance ≥ 50 MΩ (500 VDC megger) Dielectric strength Between the charging part and the case: 1,500 VAC~ 50 / 60Hz for 1 min Vibration 1.0 mm amplitude at frequency of 10 to 55 Hzin each X, Y, Z direction for 2 hours Shock 500 m/s² (≈ 50 G) in each X, Y, Z direction for 3 times Environment_Ambient temperature -25 to 70 ℃, storage: -30 to 80 ℃ (no freezing or condensation) Environment_Ambient humidity 35 to 95 %RH, storage: 35 to 95 %RH (no freezing or condensation) Protection structure IP67(IEC standard) Connection Cable type Cable Standard/material Standard type cable (black): polyvinyl chloride (PVC) Material Case/Nut: nickel plated brass (DIA. of sensing side Ø 8 mm connector type case: SUS303), washer: nickel plated iron, sensing side: PBT

Read more less

Installation Flush Sensing side diameter Ø8mm Sensing distance 1.5mm Hysteresis(distance) Max. 10% of sensing distance Standard sensing target 8×8×1mm(iron) Response frequency 1.5kHz Indicator Operation indicator (red LED) Unit weight (packaged weight) ≈ 54 g (≈ 66 g) Power voltage 12 - 24 VDC(ripple P-P: ≤ 10 %), operating voltage: 10 - 30 VDC Current specification Current consumption: Max. 10mA Control output ≤ 200 mA Residual voltage Max. 2V Protection circuit Surge protection circuit, output short over current protection circuit, reverse polarity protection circuit Insulation resistance ≥ 50 MΩ (500 VDC megger) Dielectric strength Between the charging part and the case: 1,500 VAC~ 50 / 60Hz for 1 min Vibration 1.0 mm amplitude at frequency of 10 to 55 Hzin each X, Y, Z direction for 2 hours Shock 500 m/s² (≈ 50 G) in each X, Y, Z direction for 3 times Environment_Ambient temperature -25 to 70 ℃, storage: -30 to 80 ℃ (no freezing or condensation) Environment_Ambient humidity 35 to 95 %RH, storage: 35 to 95 %RH (no freezing or condensation) Protection structure IP67(IEC standard) Connection Cable type Cable Standard/material Standard type cable (black): polyvinyl chloride (PVC) Material Case/Nut: nickel plated brass (DIA. of sensing side Ø 8 mm connector type case: SUS303), washer: nickel plated iron, sensing side: PBT

Read more less

Installation Flush Sensing side diameter Ø30mm Sensing distance 10mm Hysteresis(distance) Max. 10% of sensing distance Standard sensing target 30×30×1mm(iron) Response frequency 20Hz Indicator Operation indicator (red LED) Unit weight (packaged weight) ≈ 170 g (≈ 207 g) Power voltage 100 - 240 VAC~ 50 / 60 Hz, operating voltage: 85 - 264 VAC~ Current specification Leakage current: Max. 2.5mA Control output 5 to 200 mA Residual voltage Max. 10V Protection circuit Surge protection circuit Insulation resistance ≥ 50 MΩ (500 VDC megger) Insulation type Double insulation or reinforced insulation(mark: , dielectric strength between the measuring input part and the power part: 1kV) Dielectric strength 2,500 VAC~ 50/60 Hz for 1 minute Vibration 1.0 mm amplitude at frequency of 10 to 55 Hzin each X, Y, Z direction for 2 hours Shock 500 m/s² (≈ 50 G) in each X, Y, Z direction for 3 times Environment_Ambient temperature -25 to 70 ℃, storage: -30 to 80 ℃ (no freezing or condensation) Environment_Ambient humidity 35 to 95 %RH, storage: 35 to 95 %RH (no freezing or condensation) Protection structure IP67(IEC standard) Connection Cable type Cable Standard/material Standard type cable (black): polyvinyl chloride (PVC) Material Case/Nut: nickel plated brass, washer: nickel plated iron, sensing side: PBT

Read more less

Installation Flush Sensing side diameter Ø30mm Sensing distance 10mm Hysteresis(distance) Max. 10% of sensing distance Standard sensing target 30×30×1mm(iron) Response frequency 20Hz Indicator Operation indicator (red LED) Unit weight (packaged weight) ≈ 208 g (≈ 245 g) Power voltage 100 - 240 VAC~ 50 / 60 Hz, operating voltage: 85 - 264 VAC~ Current specification Leakage current: Max. 2.5mA Control output 5 to 200 mA Residual voltage Max. 10V Protection circuit Surge protection circuit Insulation resistance ≥ 50 MΩ (500 VDC megger) Insulation type Double insulation or reinforced insulation(mark: , dielectric strength between the measuring input part and the power part: 1kV) Dielectric strength 2,500 VAC~ 50/60 Hz for 1 minute Vibration 1.0 mm amplitude at frequency of 10 to 55 Hzin each X, Y, Z direction for 2 hours Shock 500 m/s² (≈ 50 G) in each X, Y, Z direction for 3 times Environment_Ambient temperature -25 to 70 ℃, storage: -30 to 80 ℃ (no freezing or condensation) Environment_Ambient humidity 35 to 95 %RH, storage: 35 to 95 %RH (no freezing or condensation) Protection structure IP67(IEC standard) Connection Cable type Cable Standard/material Standard type cable (black): polyvinyl chloride (PVC) Material Case/Nut: nickel plated brass, washer: nickel plated iron, sensing side: PBT

Read more less

Installation Flush Sensing side diameter Ø30mm Sensing distance 10mm Hysteresis(distance) Max. 10% of sensing distance Standard sensing target 30×30×1mm(iron) Response frequency 20Hz Indicator Operation indicator (red LED) Unit weight (packaged weight) ≈ 208 g (≈ 245 g) Power voltage 100 - 240 VAC~ 50 / 60 Hz, operating voltage: 85 - 264 VAC~ Current specification Leakage current: Max. 2.5mA Control output 5 to 200 mA Residual voltage Max. 10V Protection circuit Surge protection circuit Insulation resistance ≥ 50 MΩ (500 VDC megger) Insulation type Double insulation or reinforced insulation(mark: , dielectric strength between the measuring input part and the power part: 1kV) Dielectric strength 2,500 VAC~ 50/60 Hz for 1 minute Vibration 1.0 mm amplitude at frequency of 10 to 55 Hzin each X, Y, Z direction for 2 hours Shock 500 m/s² (≈ 50 G) in each X, Y, Z direction for 3 times Environment_Ambient temperature -25 to 70 ℃, storage: -30 to 80 ℃ (no freezing or condensation) Environment_Ambient humidity 35 to 95 %RH, storage: 35 to 95 %RH (no freezing or condensation) Protection structure IP67(IEC standard) Connection Cable type Cable Standard/material Standard type cable (black): polyvinyl chloride (PVC) Material Case/Nut: nickel plated brass, washer: nickel plated iron, sensing side: PBT

Read more less

Industrial proxim Installation Flush Sensing side diameter Ø18mm Sensing distance 5mm Hysteresis(distance) Max. 10% of sensing distance Standard sensing target 18×18×1mm(iron) Response frequency 20Hz Indicator Operation indicator (red LED) Unit weight (packaged weight) ≈ 130 g (≈ 142 g) Power voltage 100 - 240 VAC~ 50 / 60 Hz, operating voltage: 85 - 264 VAC~ Current specification Leakage current: Max. 2.5mA Control output 5 to 200 mA Residual voltage Max. 10V Protection circuit Surge protection circuit Insulation resistance ≥ 50 MΩ (500 VDC megger) Insulation type Double insulation or reinforced insulation(mark: , dielectric strength between the measuring input part and the power part: 1kV) Dielectric strength 2,500 VAC~ 50/60 Hz for 1 minute Vibration 1.0 mm amplitude at frequency of 10 to 55 Hzin each X, Y, Z direction for 2 hours Shock 500 m/s² (≈ 50 G) in each X, Y, Z direction for 3 times Environment_Ambient temperature -25 to 70 ℃, storage: -30 to 80 ℃ (no freezing or condensation) Environment_Ambient humidity 35 to 95 %RH, storage: 35 to 95 %RH (no freezing or condensation) Protection structure IP67(IEC standard) Connection Cable type Cable Standard/material Standard type cable (black): polyvinyl chloride (PVC) Material Case/Nut: nickel plated brass, washer: nickel plated iron, sensing side: PBT ity sensor for automation systems.

Read more less

Installation Flush Sensing side diameter Ø18mm Sensing distance 5mm Hysteresis(distance) Max. 10% of sensing distance Standard sensing target 18×18×1mm(iron) Response frequency 20Hz Indicator Operation indicator (red LED) Unit weight (packaged weight) ≈ 130 g (≈ 142 g) Power voltage 100 - 240 VAC~ 50 / 60 Hz, operating voltage: 85 - 264 VAC~ Current specification Leakage current: Max. 2.5mA Control output 5 to 200 mA Residual voltage Max. 10V Protection circuit Surge protection circuit Insulation resistance ≥ 50 MΩ (500 VDC megger) Insulation type Double insulation or reinforced insulation(mark: , dielectric strength between the measuring input part and the power part: 1kV) Dielectric strength 2,500 VAC~ 50/60 Hz for 1 minute Vibration 1.0 mm amplitude at frequency of 10 to 55 Hzin each X, Y, Z direction for 2 hours Shock 500 m/s² (≈ 50 G) in each X, Y, Z direction for 3 times Environment_Ambient temperature -25 to 70 ℃, storage: -30 to 80 ℃ (no freezing or condensation) Environment_Ambient humidity 35 to 95 %RH, storage: 35 to 95 %RH (no freezing or condensation) Protection structure IP67(IEC standard) Connection Cable type Cable Standard/material Standard type cable (black): polyvinyl chloride (PVC) Material Case/Nut: nickel plated brass, washer: nickel plated iron, sensing side: PBT

Read more less

Installation Flush Sensing side diameter Ø12mm Sensing distance 2mm Hysteresis(distance) Max. 10% of sensing distance Standard sensing target 12×12×1mm(iron) Response frequency 20Hz Indicator Operation indicator (red LED) Unit weight (packaged weight) ≈ 72 g (≈ 84 g) Power voltage 100 - 240 VAC~ 50 / 60 Hz, operating voltage: 85 - 264 VAC~ Current specification Leakage current: Max. 2.5mA Control output 5 to 150 mA Residual voltage Max. 10V Protection circuit Surge protection circuit Insulation resistance ≥ 50 MΩ (500 VDC megger) Insulation type Double insulation or reinforced insulation(mark: , dielectric strength between the measuring input part and the power part: 1kV) Dielectric strength 2,500 VAC~ 50/60 Hz for 1 minute Vibration 1.0 mm amplitude at frequency of 10 to 55 Hzin each X, Y, Z direction for 2 hours Shock 500 m/s² (≈ 50 G) in each X, Y, Z direction for 3 times Environment_Ambient temperature -25 to 70 ℃, storage: -30 to 80 ℃ (no freezing or condensation) Environment_Ambient humidity 35 to 95 %RH, storage: 35 to 95 %RH (no freezing or condensation) Protection structure IP67(IEC standard) Connection Cable type Cable Standard/material Standard type cable (black): polyvinyl chloride (PVC) Material Case/Nut: nickel plated brass, washer: nickel plated iron, sensing side: PBT

Read more less

Installation Flush Sensing side diameter Ø8mm Sensing distance 1.5mm Hysteresis(distance) Max. 10% of sensing distance Standard sensing target 8×8×1mm(iron) Response frequency 1.5kHz Indicator Operation indicator (red LED) Unit weight (packaged weight) ≈ 32 g (≈ 44 g) Power voltage 12 - 24 VDC(ripple P-P: ≤ 10 %), operating voltage: 10 - 30 VDC Current specification Leakage current: Max. 0.6mA Control output 2 to 100 mA Residual voltage Max. 3.5V Protection circuit Surge protection circuit, output short over current protection circuit, reverse polarity protection circuit Insulation resistance ≥ 50 MΩ (500 VDC megger) Dielectric strength Between the charging part and the case: 1,500 VAC~ 50 / 60Hz for 1 min Vibration 1.0 mm amplitude at frequency of 10 to 55 Hzin each X, Y, Z direction for 2 hours Shock 500 m/s² (≈ 50 G) in each X, Y, Z direction for 3 times Environment_Ambient temperature -25 to 70 ℃, storage: -30 to 80 ℃ (no freezing or condensation) Environment_Ambient humidity 35 to 95 %RH, storage: 35 to 95 %RH (no freezing or condensation) Protection structure IP67(IEC standard) Connection Cable connector type Connector type M12 Connector Cable Standard/material Standard type cable (black): polyvinyl chloride (PVC) Material Case/Nut: nickel plated brass (DIA. of sensing side Ø 8 mm connector type case: SUS303), washer: nickel plated iron, sensing side: PBT

Read more less

Installation Non-flush Sensing side diameter Ø8mm Sensing distance 2mm Hysteresis(distance) Max. 10% of sensing distance Standard sensing target 8×8×1mm(iron) Response frequency 1kHz Indicator Operation indicator (red LED) Unit weight (packaged weight) ≈ 32 g (≈ 44 g) Power voltage 12 - 24 VDC(ripple P-P: ≤ 10 %), operating voltage: 10 - 30 VDC Current specification Leakage current: Max. 0.6mA Control output 2 to 100 mA Residual voltage Max. 3.5V Protection circuit Surge protection circuit, output short over current protection circuit, reverse polarity protection circuit Insulation resistance ≥ 50 MΩ (500 VDC megger) Dielectric strength Between the charging part and the case: 1,500 VAC~ 50 / 60Hz for 1 min Vibration 1.0 mm amplitude at frequency of 10 to 55 Hzin each X, Y, Z direction for 2 hours Shock 500 m/s² (≈ 50 G) in each X, Y, Z direction for 3 times Environment_Ambient temperature -25 to 70 ℃, storage: -30 to 80 ℃ (no freezing or condensation) Environment_Ambient humidity 35 to 95 %RH, storage: 35 to 95 %RH (no freezing or condensation) Protection structure IP67(IEC standard) Connection Cable connector type Connector type M12 Connector Cable Standard/material Standard type cable (black): polyvinyl chloride (PVC) Material Case/Nut: nickel plated brass (DIA. of sensing side Ø 8 mm connector type case: SUS303), washer: nickel plated iron, sensing side: PBT

Read more less